1985

Exhaust

Filter Products Showing 1 - 20 of 67 results
Select Your Year
Categories
  • CONNECTING PIPE, 83-85 RX7 (WILL WORK FOR 81-82)

    CONNECTING PIPE, 83-85 RX7 (WILL WORK FOR 81-82)

    CONNECTING PIPE, 83-85 RX7 (WILL WORK FOR 81-82)

    If using for 81-82 you must use 83-85 muffler

    Connecting Pipe Section
    1983-85 RX-7

    We offer a replacement connecting pipe section for the pipe section located between the primary (monolith) catalytic and muffler unit. The Racing Beat connecting pipe section is produced using mandrel-bent 2″ OD thick-wall stainless steel tubing and utilizes laser-cut stainless-steel flanges. Also included is separate hanger bracket to support the forward end of the connecting pipe. Although the stock rubber hangers can be reused, we strongly suggest replacing old, worn rubber hangers with new hangers to ensure correct chassis alignment of the exhaust system.

    Installation Notes:

    – This connecting pipe is NOT supplied with mounting positions for the stock heat shield. The heat shield cannot retained on this application.

    – This connecting pipe is NOT supplied with a mounting position for the “Exhaust Temperature Sensor” unit. This sensor is used to monitor exhaust temperature and will signal a dash warning light if exhaust temperature exceeds a predetermined limit. This sensor can be eliminated or re-positioned away from the exhaust.

    SKU: 16203
    $175.00
    Add to cart
  • ENGINE TO PIPE FLANGE 12A

    ENGINE TO PIPE FLANGE 12A

    12A Engine To Pipe Flange 74-85

    This 1/2″ thick laser-cut engine-to-header exhuast flange can be used to fabricate a custom exhaust system for any 1974-85 12A rotary engine. This is the same flange that is used on Racing Beat’s 12A engine- headers.

    SKU: 16182
    $47.30
    Add to cart
  • ENGINE TO PIPE FLANGE, 13B

    ENGINE TO PIPE FLANGE, 13B

    Engine to Pipe Flange, 13B 79-95 all turbo and non-turbo

    This 1/2″ thick laser-cut engine-to-header exhaust flange can be used to fabricate a custom exhaust system for any 13B rotary engine. This is the same exhaust flange that is used on Racing Beat’s 13B engine headers.

    SKU: 16183
    $47.30
    Add to cart
  • EXHAUST CENTER SECTION, 79-85 RB 4 PORT/6 PORT

    EXHAUST CENTER SECTION, 79-85 RACING BEAT 4 PORT/6 PORT

    Racing Beat Exhaust Center Section, 79-85 4 Port/6 Port

    SKU: 16398
    $605.17
    Add to cart
  • EXHAUST CENTER SECTION, 84-85 13B WITH 6 PORT TUBE

    EXHAUST CENTER SECTION, 84-85 13B WITH 6 PORT TUBE

    Racing Beat Exhaust Center Section, 84-85 13B With 6 Port Tube

    SKU: 16399
    $605.17
    Add to cart
  • EXHAUST COLLECTOR, UNFLANGED Y PIPE

    EXHAUST COLLECTOR, UNFLANGED Y PIPE

    Racing Beat Unflanged Exhaust Collector Y Pipe

    SKU: 16004
    $121.28
    Add to cart
  • EXHAUST HANGER SUPPORT 79-85

    EXHAUST HANGER SUPPORT 79-85

    Exhaust Hanger Support 79-85

    These hangers were used by Mazda on the early 1979-85 RX-7 mufflers as part of a “rubber hanger/metal hanger” combination to secure the muffler to the chassis. While this arrangement was rather bulky and required multiple components, it did however allow for irregularities in the exhaust system fitment and provided excellent vibration dampening.

    We offer this hanger for use as a replacement for a failed or rusted stock unit. Produced from heavy gauge steel and zinc coated for excellent corrosion protection. If you are replacing the rubber hangers on your muffler, now is the time to complete a full upgrade to all new and much better looking metal hangers!

    Three (3) hangers required for each muffler. SOLD INDIVIDUALLY.

    SKU: 16337
    $14.43
    Add to cart
  • EXHAUST HEADER 12A, 79-85 RX7 DUAL OUTLET

    EXHAUST HEADER 12A, 79-85 RX7 DUAL OUTLET

    Racing Beat 12A Exhaust Header, 79-85 RX7 Dual Outlet

    SKU: 16125
    $375.95
    Add to cart
  • EXHAUST HEADER 12A, 84-85 RX7 MANUAL TRANS

    EXHAUST HEADER 12A, 84-85 RX7 (MANUAL TRANSMISSION)

    Racing Beat 12A Exhaust Header, 84-85 RX7 with Manual Transmission
    Actual header not shown in photo – oxygen sensor fitting only included on 1984-85 RX-7 GSL-SE header.

    The Racing Beat RX-7 Header is designed for a bolt-on installation, when used with the appropriate Power Pulse Presilencer in all 1984-85 RX-7s (12A – Manual Transmission). The combination of this RX-7 exhaust header and the appropriate presilencer replaces the stock exhaust manifold and all catalytic converters for use in racing applications, along with any intermediate pieces of tubing.

    This RX-7 header assembly is constructed with .120-inch wall, mandrel-bend, mild steel tubing for increased durability. The engine-to-header flange is laser-cut from .5-inch thick steel plate to ensure positive gas sealing. An outlet gasket is included. An engine-to-header gasket is available separately if needed.

    SKU: 16012
    $389.30
    Add to cart
  • EXHAUST HEADER 12A, 84-85 RX7 AUTO TRANSMISSION

    EXHAUST HEADER 12A, 84-85 RX7 AUTOMATIC TRANSMISSION

    Racing Beat 12A Exhaust Header, 84-85 RX7 Automatic Transmission

    This Streetable Header/Collector is designed for a bolt-on installation, when used with the appropriate Power Pulse Presilencer in all 1984-85 RX-7 (12A – Automatic Transmission) models. The combination of this Header/Collector and the appropriate presilencer replaces the stock exhaust manifold and all catalytic converters, along with any intermediate pieces of tubing.

    The Header/Collector assembly is constructed with .120-inch wall, mandrel-bend, mild steel tubing for increased durability. Both flanges are flame-cut from .4375-inch thick steel plate for positive gas sealing. An outlet gasket is included. An engine-to-header gasket is available separately if needed.

    SKU: 16014
    $389.30
    Add to cart
  • EXHAUST HEADER , KIT (DISASSEMBLED)

    EXHAUST HEADER 12A, KIT (DISASSEMBLED)

    Racing Beat 12A Exhaust Header Kit (Disassembled)

    SKU: 16211
    $197.68
    Add to cart
Shopping Cart
Products
0
Total
$0.00
Cart
0