EXHAUST HANGER, 2 SLEEVES
Exhaust Hanger, 2 Sleeves
Go To Our FAQ for Exhaust Hangers to see the locations and part numbers of the hangers for your car.
| SKU: | 40-1600-1114 |
| Manufacturer SKU: | 1114-40-160 |
EXHAUST HANGER, 2 SLEEVES
Go To Our FAQ for Exhaust Hangers to see the locations and part numbers of the hangers for your car.
$32.96
Related Products:
-
EXHAUST SYSTEM SINGLE, 84-85 RX7 13B GSLSE
Racing Beat Single Exhuast System, 84-85 13B SE
Racing Beat offers a complete RX-7 high-performance exhaust system for the 1984-85 13B (GSL-SE) RX-7. This system includes our Road Race Header, a Power-Pulse Presilencer, and our legendary Power Pulse main muffler. The Power Pulse Presilencer unit is equipped with an exhaust backpressure pickup tube that allows the correct operation of the 6-Port intake actuators. Be careful, if you are considering a replacement exhaust system that does not have this important feature, your intake system will not perform correctly and a noticeable decrease in high RPM performance will occur.
These components attach to all stock mounting points, and include all necessary gaskets and hardware. The only component not included is the factory connecting pipe that mounts just ahead of the main muffler. There is no horsepower to be gained by replacing this pipe with a larger diameter assembly. If your factory connecting pipe needs replacing, we suggest you contact your local muffler shop.
These exhaust systems offer excellent horsepower gains when you require a muffled exhaust system for your stock-ported engine. The actual horsepower increase depends on which year/model stock RX-7 exhaust system you are comparing to, but a 22% increase at 7000 rpm is typical. Thanks to the combined efforts of the Power-Pulse Presilencer and the Power Pulse Main muffler, the exhaust noise is only slightly higher than stock, with a very low, pleasant character.
.
SKU: 16421 -
EXHAUST HANGER, 86-92 RX7 @ “Y” PIPE
Exhaust Hanger at “Y” Pipe, 86-92
Go To Our FAQ for Exhaust Hangers to see the locations and part numbers of the hangers for your car.
SKU: 40-060B-N326 Manufacturer SKU: N326-40-060B -
EXHAUST SYSTEM DUAL, 12A DUAL PIPE 79-85 RX7
Racing Beat Dual Exhaust System, 12A Dual Pipe 79-85
SKU: 16422 -
EXHAUST SYSTEM SINGLE, 86-92 RX7 NON TURBO WITH RACING BEAT REAR MUFFLERS
Single Exhaust System, 86-92 Non Turbo with Racing Beat Rear Mufflers
SKU: 16-MZTX-0020RB -
EXHAUST SYSTEM, 86-92 RX7 TURBO
Racing Beat Exhaust System, 86-92 Turbo
1987-91 RX-7 TURBO REV II Complete High Performance Exhaust System – If you own a TURBO II RX-7 and you’ve found your way to this webpage, congratulations! Why? Because your search for an exhaust system for your car ends here. Simply put, this is the ultimate exhaust for any Turbo II RX-7!
The REV TII High Performance RX-7 Exhaust is legendary with FC3S owners. This RX-7 exhaust system includes a 3-inch OD REV TII Down Pipe from the turbo outlet that mates to a REV TII Presilencer section. The outlet of the presilencer connects to the inlet of the REV TII Y-Pipe which routes the exhaust gases down two 2.375-inch OD (60mm) pipes into a pair of left and right REV TII Power Pulse Mufflers. Once installed, this bolt-on exhaust system increases horsepower approximately 32% – that’s a 59 HP increase on a 1987 Turbo II RX-7!
The REV TII High Performance RX-7 Exhaust system reduces exhaust gas back-pressure significantly, thereby allowing the un-assisted turbo boost pressure to increase to 10-11 psi. (Note: A fuel cut controller device is required to prevent fuel cutoff to the rear rotor above the factory pre-set limit.)
This bolt-on system uses the stock mounting points for ease of installation. Each system is supplied with all necessary mounting hardware and gaskets. (The kit does not include turbo outlet gasket, if needed it can be ordered separately.) The down pipe section is provided with a position for the oxygen sensor.
SKU: 16425 -
EXHAUST HANGER, 86-92 RX7 BAND+ SLEEVE
Exhaust Hanger with Steel Band around it and a sleeve, 86-92
Go To Our FAQ for Exhaust Hangers to see the locations and part numbers of the hangers for your car.
SKU: 40-060B-N328 Manufacturer SKU: N328-40-060B
You May Also Like:
-
EXHAUST HEADER 13B, 74-78 NO FLANGE EXCEPT PICK UP
Racing Beat 13B Exhaust Header, 74-78 No Flange. Will not work on the Pick Up
This rotary exhaust Header/Collector (less outlet flange) is ideal for RX-2, RX-3, RX-4, and COSMO (does not fit rotary pickup) custom exhaust installations. The flame-cut, .5-inch thick engine flange provides positive sealing and alignment. By integrating the collector with the header we reduce the effort and cost in completing the exhaust system. Engine-to-pipe gaskets are not included but are available separately. An Air Control and Check Valve Cover Plate is required when using this header with a stock intake system.
If the stock resonator is eliminated during installation of this unit, we strongly recommend selecting a Power Pulse Presilencer and installing it in place of the resonator to maintain a pleasant noise level and character.
SKU: 16007 -
-
EXHAUST HEADER 12A, 79-85 RX7 DUAL OUTLET
Racing Beat 12A Exhaust Header, 79-85 RX7 Dual Outlet
SKU: 16125 -
-
EXHAUST PRE-SILENCER, 81-83 RX7
Racing Beat Exhaust Pre-Silencer, 71-78, 81-83
The Racing Beat Power Pulse Presilencer for the 1971-78 & 81-83 RX-7 is designed to be used with our wide selection of RX-7 Streetable Headers to complete a bolt-on configuration. These Power Pulse Presilencers are ideal for those individuals wanting to fabricate custom exhaust systems incorporating either long or short primary exhaust systems.
The Power Pulse Presilencer improves the character of the exhaust noise, dramatically reducing the inherent, obnoxious metallic high frequency noise with virtually no power loss. Constructed with a high temperature, 2-inch I.D. perforated core of 304 stainless steel wrapped with high-temperature stainless steel wool, the Power Pulse Presilencer measures 20 inches in length with a 4-inch outside diameter. The mounting studs are 12mm both front and rear.
SKU: 16400 -
EXHAUST HEADER 13B, 89-92 RX7 6-PORT DUAL PIPE
Racing Beat 13B Exhaust Header, 89-92 With 6 Port Actuation and O2 sensor fitting.
SKU: 16129