EXHAUST NUT, 12MM CATALYTIC CONVERTER 17MM HEX
12mm x 1.25 (fine thread) Nut for catalytic converter studs
EXHAUST NUT, 12MM CATALYTIC CONVERTER 17MM HEX
| SKU: | 40-3550-8118 |
| Manufacturer SKU: | 8118-40-355 |
EXHAUST NUT, 12MM CATALYTIC CONVERTER 17MM HEX
$12.07
Related Products:
-
EXHAUST HEADER 12A, 79-85 RX7 DUAL OUTLET
Racing Beat 12A Exhaust Header, 79-85 RX7 Dual Outlet
SKU: 16125 -
EXHAUST HEADER 13B, 86-92 RX7 NON-TURBO
Racing Beat 13B 6 Port Exhaust Header, 86-92 RX7 Non-Turbo
Racing Beat’s rotary exhaust Header/Collector is designed for a bolt-on installation, when used with the appropriate Power Pulse Presilencer, in all 1986-92 non-turbo RX-7s. The combination of this Header/Collector and the appropriate presilencer replaces the stock exhaust manifold and all catalytic converters, along with any intermediate pieces of tubing. (In this application, the presilencer will bolt-up to the factory Y-pipe.)
The Header/Collector assembly is constructed with .120″ wall, mandrel-bent, mild steel tubing (2″ OD primary, 2.5″ OD secondary) for excellent durability and noise suppression. Both flanges are laser cut from 7/16″ thick steel plate for positive gas sealing. An outlet gasket is included. An engine-to-header gasket is available separately if needed. This header is equipped with an oxygen sensor fitting.
SKU: 16130 -
EXHAUST HEADER 13B, 79-92 4&6-PORT DUAL OUTLET
Racing Beat 13B Exhaust Header, 79-92 4&6-PORT DUAL OUTLET
SKU: 16127 Manufacturer SKU: 16127 -
EXHAUST NUT, 10X1.50 EXHAUST MANIFOLD
Exhaust Nut, 10X1.50 All 74-92 rotor housing stud
SKU: 40-3550-8134 Manufacturer SKU: 8134-40-355 -
EXHAUST HEADER 12A, 84-85 RX7 AUTOMATIC TRANSMISSION
Racing Beat 12A Exhaust Header, 84-85 RX7 Automatic Transmission
This Streetable Header/Collector is designed for a bolt-on installation, when used with the appropriate Power Pulse Presilencer in all 1984-85 RX-7 (12A – Automatic Transmission) models. The combination of this Header/Collector and the appropriate presilencer replaces the stock exhaust manifold and all catalytic converters, along with any intermediate pieces of tubing.
The Header/Collector assembly is constructed with .120-inch wall, mandrel-bend, mild steel tubing for increased durability. Both flanges are flame-cut from .4375-inch thick steel plate for positive gas sealing. An outlet gasket is included. An engine-to-header gasket is available separately if needed.
SKU: 16014 -
EXHAUST STUD, ROTARY HEADER STUD
Rotary Header Stud All 74-92
Stud, rotor housing for exhaust manifoldSKU: 10-1050-0839 Manufacturer SKU: 0839-10-105
You May Also Like:
-
EXHAUST CONVERTER GASKET 93-95 MAIN FRONT & REAR
Exhaust Converter Gasket 93-95 Front and Rear of Main
SKU: 40-3050-RF36 Manufacturer SKU: RF36-40-305 -
-
-
-
EXHAUST PRE-SILENCER WITH DOWN PIPE, 88 CONVERTIBLE MANUAL
Racing Beat Exhaust Pre-Silencer with Down Pipe, 88 Convertible Manual Transmission Non-Turbo
Down Pipe with Presilencer – 1988 RX-7 Convertible Non-Turbo (w/Manual Transmission) – The 1986-92 13B 6-port engines, in stock form with the factory fuel injection, produces similar power gains with either our Header/Presilencer combo or our RX-7 Down Pipe/Presilencer combination. If you have no intentions of installing RB’s Holley intake System (or any other aftermarket carb set-up), we recommend the use of the down pipe/Presilencer combo since it offers a slightly quieter exhaust note, is easier to install and less costly. If you are intending to upgrade the intake or fuel injection system, the Header/Presilencer combo offers the greatest performance potential.
The 1988 RX-7 Convertible (w/ Manual Transmission) Down Pipe/Presilencer combination incorporates a 2.5-inch O.D. Down Pipe and our perforated stainless steel core and stainless steel wool-packed Presilencer to boost power approximately 13% – an 18 horsepower increase on a 1987 RX 7- and maintain a comfortable exhaust noise level during full power driving.
The replacement pipe connects to the factory exhaust manifold, and the presilencer connects to the factory Y-pipe, replacing all catalytic converters and intermediate tubing. (The downpipe cannot be used as a “bolt-up” component to replace just the catalytic converters.)
The Racing Beat presilencer is equipped with an exhaust back-pressure tube for correct operation of the 6-port actuators. Installation of this requires the removal of the air control and check valve and the air pump. This kit includes all necessary mounting hardware, air control & check valve cover plate, and gaskets (1 Back Pressure Pick-up and 3 Replacement Pipe-to-Presilencer gaskets).
SKU: 16209 -
