EXHAUST HANGER, 86-92 BAND+ SLEEVE
Exhaust Hanger with Steel Band around it and a sleeve, 86-92
Go To Our FAQ for Exhaust Hangers to see the locations and part numbers of the hangers for your car.
| SKU: | 40-060B-N328 |
| Manufacturer SKU: | N328-40-060B |
EXHAUST HANGER, 86-92 BAND+ SLEEVE
$33.32
Related Products:
-
-
EXHAUST HANGER, 86-92 @ “Y” PIPE
Exhaust Hanger at “Y” Pipe, 86-92
Go To Our FAQ for Exhaust Hangers to see the locations and part numbers of the hangers for your car.
SKU: 40-060B-N326 Manufacturer SKU: N326-40-060B -
MUFFLER PAIR+”Y”PIPE, 86-92 ALL RACING BEAT
Racing Beat Muffler (Pair) +”Y” Pipe, 86-92 All
1986-92 RX-7 Street Exhaust System
The Racing Beat street legal, Power Pulse cat-back RX-7 exhaust system is the perfect replacement for your RX-7 exhaust – a durable assembly offering a real horsepower gain over your stock unit. If you need to retain the emissions status of your RX-7 and keep the sound level to a tolerable level – look no further than this Racing Beat system!The RX-7 exhaust system consists of a Racing Beat Y-pipe and two 2.375″-inch (OD) 304-stainless steel Power Pulse mufflers. The replacement Y-pipe is manufactured using 2.5-inch (OD) tubing, splitting off into a pair of 2-inch (OD) tubes feeding the left and right Power Pulse Muffler canisters.
Careful consideration was given to the correct placement of each muffler canister with regards to the opening in the rear bumper. Racing Beat positioned the muffler canister “under” the rear bumper in order to present a more integrated look. Unlike many aftermarket systems that use a simple universal muffler, the Racing Beat system utilizes a rotary-engine designed muffler that has been specifically designed for the 1986-92 RX-7 application.
Performance tests on a Dyno Jet chassis dyno have shown a 7.3 HP gain over the stock system (stock Turbo II). This bolt-on system uses the stock mounting points for ease of installation. Each system is supplied with all necessary mounting hardware and gaskets.
SKU: 16418 -
EXHAUST SYSTEM SINGLE, 86-92 NON TURBO WITH RACING BEAT REAR MUFFLERS
Single Exhaust System, 86-92 Non Turbo with Racing Beat Rear Mufflers
SKU: 16-MZTX-0020RB -
EXHAUST HANGER, 2 SLEEVES
Exhaust Hanger, 2 Sleeves
Go To Our FAQ for Exhaust Hangers to see the locations and part numbers of the hangers for your car.
SKU: 40-1600-1114 Manufacturer SKU: 1114-40-160 -
EXHAUST SYSTEM, 86-92 TURBO
Racing Beat Exhaust System, 86-92 Turbo
1987-91 RX-7 TURBO REV II Complete High Performance Exhaust System – If you own a TURBO II RX-7 and you’ve found your way to this webpage, congratulations! Why? Because your search for an exhaust system for your car ends here. Simply put, this is the ultimate exhaust for any Turbo II RX-7!
The REV TII High Performance RX-7 Exhaust is legendary with FC3S owners. This RX-7 exhaust system includes a 3-inch OD REV TII Down Pipe from the turbo outlet that mates to a REV TII Presilencer section. The outlet of the presilencer connects to the inlet of the REV TII Y-Pipe which routes the exhaust gases down two 2.375-inch OD (60mm) pipes into a pair of left and right REV TII Power Pulse Mufflers. Once installed, this bolt-on exhaust system increases horsepower approximately 32% – that’s a 59 HP increase on a 1987 Turbo II RX-7!
The REV TII High Performance RX-7 Exhaust system reduces exhaust gas back-pressure significantly, thereby allowing the un-assisted turbo boost pressure to increase to 10-11 psi. (Note: A fuel cut controller device is required to prevent fuel cutoff to the rear rotor above the factory pre-set limit.)
This bolt-on system uses the stock mounting points for ease of installation. Each system is supplied with all necessary mounting hardware and gaskets. (The kit does not include turbo outlet gasket, if needed it can be ordered separately.) The down pipe section is provided with a position for the oxygen sensor.
SKU: 16425
You May Also Like:
-
-
EXHAUST SYSTEM DUAL, 13B DUAL PIPE 79-85
Racing Beat 13B 4 Port Dual Pipe Exhaust System 79-85
Will work on 6 Port if not using the actuators.SKU: 16423 -
Exhaust Down Pipe 86-92 Non-Turbo Coupes 2 1/2″
Exhaust Down Pipe 86-92 Non-Turbo Coupes 2 1/2″
This Down Pipe is available for custom applications in a 1986-91 RX-7 (excluding convertible) non-turbo application. This 2.5-inch down pipe fits either manual or automatic transmission equipped cars and eliminates the catalytic converter sections.
This down pipe bolts to the stock exhaust manifold, but the use of our presilencer (or a suitable replacement) is required to connect this assembly to the Y-pipe section. If you need to retain a catalytic converter in your exhaust system, you may find a suitable unit offered in the aftermarket. Although the replacement of your stock catalytic converters with a single aftermarket unit is technically NOT legal, this approach may suit your emissions needs. We suggest you contact your local emissions testing facility for more information. Gaskets sold separately.
SKU: S16206 -
EXHAUST PRE-SILENCER, 81-83
Racing Beat Exhaust Pre-Silencer, 71-78, 81-83
The Racing Beat Power Pulse Presilencer for the 1971-78 & 81-83 RX-7 is designed to be used with our wide selection of RX-7 Streetable Headers to complete a bolt-on configuration. These Power Pulse Presilencers are ideal for those individuals wanting to fabricate custom exhaust systems incorporating either long or short primary exhaust systems.
The Power Pulse Presilencer improves the character of the exhaust noise, dramatically reducing the inherent, obnoxious metallic high frequency noise with virtually no power loss. Constructed with a high temperature, 2-inch I.D. perforated core of 304 stainless steel wrapped with high-temperature stainless steel wool, the Power Pulse Presilencer measures 20 inches in length with a 4-inch outside diameter. The mounting studs are 12mm both front and rear.
SKU: 16400 -
-
EXHAUST HEADER 13B, 89-92 6PORT DUAL PIPE
Racing Beat 13B Exhaust Header, 89-92 With 6 Port Actuation and O2 sensor fitting.
SKU: 16129