EXHAUST STUD RX8, MAIN CAT FRONT (EA)
Exhaust Stud RX8 , Main Cat Front (EA) (3 Required)
| SKU: | 20-WA10-N3H1 |
| Manufacturer SKU: | N3H1-20-WA1 |
EXHAUST STUD RX8, MAIN CAT FRONT (EA)
$5.10
Related Products:
-
EXHAUST STUD, RENESIS EXHAUST MANIFOLD TO ENGINE
Exhaust Stud Renesis, Exhaust Manifold to Engine (4 Required)
SKU: 13-708A-SL50 Manufacturer SKU: SL50-13-708A -
EXHAUST NUT 93-95 TURBO TO MANIFOLD (USES 5) & 04-11 MANIFOLD TO CAT
Exhaust Nut 93-95, Turbo To Manifold (USES 5) 10mm
This nut is also the correct nut for 04-11 RX8 at the front of the catalytic converter to the exhaust manifold
SKU: 40-3550-JE10 Manufacturer SKU: JE10-40-355 -
EXHAUST NUT RX8, REAR OF CAT (2 Required)
Exhaust Nut RX8, Rear of Cat (2 Required)
SKU: 01-0030-9994 Manufacturer SKU: 9994-01-003 -
EXHAUST STUD RX8, MAIN CAT REAR (EACH)
Exhaust Stud RX8, Main Cat Rear (Each)(2 Required)
SKU: 40-5840-B31R Manufacturer SKU: B31R-40-584 -
EXHAUST SPRING RX8, REAR OF CATALYTIC CONVERTER
Exhaust Spring RX8, Rear of Catalytic Converter (2 Required)
SKU: 40-582A-YJ15 Manufacturer SKU: YJ15-40-582A -
EXHAUST STUD, 12MM @ CAT —NLA—
EXHAUST STUD, 12MM AT CAT
Sorry, this item has been discontinued by Mazda.
SKU: 40-3980-1259 Manufacturer SKU: 1259-40-398
You May Also Like:
-
-
EXHAUST HANGER, 2 SLEEVES
Exhaust Hanger, 2 Sleeves
Go To Our FAQ for Exhaust Hangers to see the locations and part numbers of the hangers for your car.
SKU: 40-1600-1114 Manufacturer SKU: 1114-40-160 -
-
EXHAUST PRE-SILENCER WITH DOWN PIPE, 88 CONVERTIBLE MANUAL
Racing Beat Exhaust Pre-Silencer with Down Pipe, 88 Convertible Manual Transmission Non-Turbo
Down Pipe with Presilencer – 1988 RX-7 Convertible Non-Turbo (w/Manual Transmission) – The 1986-92 13B 6-port engines, in stock form with the factory fuel injection, produces similar power gains with either our Header/Presilencer combo or our RX-7 Down Pipe/Presilencer combination. If you have no intentions of installing RB’s Holley intake System (or any other aftermarket carb set-up), we recommend the use of the down pipe/Presilencer combo since it offers a slightly quieter exhaust note, is easier to install and less costly. If you are intending to upgrade the intake or fuel injection system, the Header/Presilencer combo offers the greatest performance potential.
The 1988 RX-7 Convertible (w/ Manual Transmission) Down Pipe/Presilencer combination incorporates a 2.5-inch O.D. Down Pipe and our perforated stainless steel core and stainless steel wool-packed Presilencer to boost power approximately 13% – an 18 horsepower increase on a 1987 RX 7- and maintain a comfortable exhaust noise level during full power driving.
The replacement pipe connects to the factory exhaust manifold, and the presilencer connects to the factory Y-pipe, replacing all catalytic converters and intermediate tubing. (The downpipe cannot be used as a “bolt-up” component to replace just the catalytic converters.)
The Racing Beat presilencer is equipped with an exhaust back-pressure tube for correct operation of the 6-port actuators. Installation of this requires the removal of the air control and check valve and the air pump. This kit includes all necessary mounting hardware, air control & check valve cover plate, and gaskets (1 Back Pressure Pick-up and 3 Replacement Pipe-to-Presilencer gaskets).
SKU: 16209 -
-
EXHAUST HEADER 12A, 79-85 RX7 DUAL OUTLET
Racing Beat 12A Exhaust Header, 79-85 RX7 Dual Outlet
SKU: 16125