EXHAUST STUD, RENESIS EXHAUST MANIFOLD TO ENGINE
Exhaust Stud Renesis, Exhaust Manifold to Engine (4 Required)
| SKU: | 13-708A-SL50 |
| Manufacturer SKU: | SL50-13-708A |
EXHAUST STUD, RENESIS EXHAUST MANIFOLD TO ENGINE
$11.36
Related Products:
-
EXHAUST NUT RX8, REAR OF CAT (2 Required)
Exhaust Nut RX8, Rear of Cat (2 Required)
SKU: 01-0030-9994 Manufacturer SKU: 9994-01-003 -
EXHAUST STUD, 12MM @ CAT —NLA—
EXHAUST STUD, 12MM AT CAT
Sorry, this item has been discontinued by Mazda.
SKU: 40-3980-1259 Manufacturer SKU: 1259-40-398 -
EXHAUST STUD RX8, MAIN CAT REAR (EACH)
Exhaust Stud RX8, Main Cat Rear (Each)(2 Required)
SKU: 40-5840-B31R Manufacturer SKU: B31R-40-584 -
EXHAUST NUT 93-95 TURBO TO MANIFOLD (USES 5) & 04-11 MANIFOLD TO CAT
Exhaust Nut 93-95, Turbo To Manifold (USES 5) 10mm
This nut is also the correct nut for 04-11 RX8 at the front of the catalytic converter to the exhaust manifold
SKU: 40-3550-JE10 Manufacturer SKU: JE10-40-355 -
EXHAUST SPRING RX8, REAR OF CATALYTIC CONVERTER
Exhaust Spring RX8, Rear of Catalytic Converter (2 Required)
SKU: 40-582A-YJ15 Manufacturer SKU: YJ15-40-582A -
EXHAUST STUD RX8, MAIN CAT FRONT (EA)
Exhaust Stud RX8 , Main Cat Front (EA) (3 Required)
SKU: 20-WA10-N3H1 Manufacturer SKU: N3H1-20-WA1
You May Also Like:
-
-
-
-
EXHAUST HEADER 12A, 81-83 RX7
Racing Beat 12A Exhaust Header, 81-83 RX7. Actual header not shown in photo – oxygen sensor fitting only included on 1984-85 RX-7 GSL-SE header.
This Racing Beat RX-7 Header is designed for a bolt-on installation, when used with the appropriate Racing Beat Power Pulse Presilencer in all 1981-83 RX-7s. The combination of this RX-7 header and the appropriate presilencer replaces the stock exhaust manifold and all catalytic converters for use on racing applications, along with any intermediate pieces of tubing.
The Racing Beat RX-7 header assembly is constructed with .120-inch wall, mandrel-bend, mild steel tubing for increased durability. The engine-to-header flange is laser-cut from 1/2-inch thick steel plate to ensure positive gas sealing. An outlet gasket is included. An engine-to-header gasket is available separately if needed.
SKU: 16010 -
EXHAUST PRE-SILENCER WITH DOWN PIPE, 88 CONVERTIBLE MANUAL
Racing Beat Exhaust Pre-Silencer with Down Pipe, 88 Convertible Manual Transmission Non-Turbo
Down Pipe with Presilencer – 1988 RX-7 Convertible Non-Turbo (w/Manual Transmission) – The 1986-92 13B 6-port engines, in stock form with the factory fuel injection, produces similar power gains with either our Header/Presilencer combo or our RX-7 Down Pipe/Presilencer combination. If you have no intentions of installing RB’s Holley intake System (or any other aftermarket carb set-up), we recommend the use of the down pipe/Presilencer combo since it offers a slightly quieter exhaust note, is easier to install and less costly. If you are intending to upgrade the intake or fuel injection system, the Header/Presilencer combo offers the greatest performance potential.
The 1988 RX-7 Convertible (w/ Manual Transmission) Down Pipe/Presilencer combination incorporates a 2.5-inch O.D. Down Pipe and our perforated stainless steel core and stainless steel wool-packed Presilencer to boost power approximately 13% – an 18 horsepower increase on a 1987 RX 7- and maintain a comfortable exhaust noise level during full power driving.
The replacement pipe connects to the factory exhaust manifold, and the presilencer connects to the factory Y-pipe, replacing all catalytic converters and intermediate tubing. (The downpipe cannot be used as a “bolt-up” component to replace just the catalytic converters.)
The Racing Beat presilencer is equipped with an exhaust back-pressure tube for correct operation of the 6-port actuators. Installation of this requires the removal of the air control and check valve and the air pump. This kit includes all necessary mounting hardware, air control & check valve cover plate, and gaskets (1 Back Pressure Pick-up and 3 Replacement Pipe-to-Presilencer gaskets).
SKU: 16209 -
EXHAUST HEADER 13B, 74-78 NO FLANGE EXCEPT PICK UP
Racing Beat 13B Exhaust Header, 74-78 No Flange. Will not work on the Pick Up
This rotary exhaust Header/Collector (less outlet flange) is ideal for RX-2, RX-3, RX-4, and COSMO (does not fit rotary pickup) custom exhaust installations. The flame-cut, .5-inch thick engine flange provides positive sealing and alignment. By integrating the collector with the header we reduce the effort and cost in completing the exhaust system. Engine-to-pipe gaskets are not included but are available separately. An Air Control and Check Valve Cover Plate is required when using this header with a stock intake system.
If the stock resonator is eliminated during installation of this unit, we strongly recommend selecting a Power Pulse Presilencer and installing it in place of the resonator to maintain a pleasant noise level and character.
SKU: 16007