EXHAUST TIP, 79-85 ALL
Exhaust Tip, 79-85 All
| SKU: | 40-5510-8871 |
| Manufacturer SKU: | 8871-40-551 |
EXHAUST TIP, 79-85 ALL
$33.12
Related Products:
-
EXHAUST SYSTEM DUAL, 84-85 13B 6 PORT
Racing Beat Dual Exhaust System, 84-85 13B 6 Port (using a carburetor)
Our Racing Beat-designed, “Long Primary” Street Port Complete RX-7 Exhaust System is designed for any 1979-85 RX-7 with a 13B street-ported engine. Designed specifically to optimize the performance benefit of a ported rotary engine, this RX-7 exhaust system will provide the maximum power output possible from an aftermarket RX-7 exhaust system. While louder than the stock system, the dual resonated center section offers maximum exhaust gas flow and scavenging while reducing sound output to a modest level.
Offered as a packaged set, this kit consists of a Road Race Header, the Street Port Center Section (for a 13B 6-Port engine), and a high flow Power Pulse Main muffler.
The Long Primary system typically adds 5% or more horsepower over a standard Short Primary system on a street ported engine, especially at higher RPMs. This system can also be used on non-ported engines with good results. It is strictly bolt-on, with no welding required. These complete “bolt-on” systems come complete with all required mounting hardware and gaskets. The center section for this application includes an exhaust backpressure pickup for to allow the correct operation of the 6-Port intake actuators. Since this is intended for racing applications, there is no provision for an oxygen sensor on this system.
SKU: 16424 -
EXHAUST SYSTEM SINGLE, 84-85 13B SE
Racing Beat Single Exhuast System, 84-85 13B SE
Racing Beat offers a complete RX-7 high-performance exhaust system for the 1984-85 13B (GSL-SE) RX-7. This system includes our Road Race Header, a Power-Pulse Presilencer, and our legendary Power Pulse main muffler. The Power Pulse Presilencer unit is equipped with an exhaust backpressure pickup tube that allows the correct operation of the 6-Port intake actuators. Be careful, if you are considering a replacement exhaust system that does not have this important feature, your intake system will not perform correctly and a noticeable decrease in high RPM performance will occur.
These components attach to all stock mounting points, and include all necessary gaskets and hardware. The only component not included is the factory connecting pipe that mounts just ahead of the main muffler. There is no horsepower to be gained by replacing this pipe with a larger diameter assembly. If your factory connecting pipe needs replacing, we suggest you contact your local muffler shop.
These exhaust systems offer excellent horsepower gains when you require a muffled exhaust system for your stock-ported engine. The actual horsepower increase depends on which year/model stock RX-7 exhaust system you are comparing to, but a 22% increase at 7000 rpm is typical. Thanks to the combined efforts of the Power-Pulse Presilencer and the Power Pulse Main muffler, the exhaust noise is only slightly higher than stock, with a very low, pleasant character.
.
SKU: 16421 -
EXHAUST SYSTEM SINGLE, 84-85 12A MANUAL
Racing Beat Single Exhaust System, 84-85 12A with Manual Transmission
SKU: 16417 -
EXHAUST SYSTEM SINGLE, 84-85 12A AUTOMATIC TRANSMISSION
Racing Beat Single Exhaust System, 84-85 12A with Automatic Transmission
Racing Beat offers a complete RX-7 high-performance exhaust system for the 1984-85 12A RX-7 (w/automatic transmission) which includes our Header/Collector, a Power-Pulse Presilencer, and our legendary Power Pulse main muffler. These components attach to all stock mounting points, and include all necessary gaskets and hardware. The only component not included is the factory connecting pipe that mounts just ahead of the main muffler. There is no horsepower to be gained by replacing this pipe with a larger diameter assembly. If your factory connecting pipe needs replacing, we suggest you contact your local Mazda dealer or muffler shop.
These exhaust systems offer excellent horsepower gains when you require a muffled exhaust system for your stock-ported engine. The actual horsepower increase depends on which year/model stock RX-7 exhaust system you are comparing to, but a 22% increase at 7000 rpm is typical. Thanks to the combined efforts of the Power-Pulse Presilencer and the Power Pulse Main muffler, the exhaust noise is only slightly higher than stock, with a very low, pleasant character.
SKU: 16419 -
EXHAUST SYSTEM DUAL, 84-85 13B 6-PORT
EXHAUST SYSTEM DUAL, 84-85 13B 6-PORT
Dual Exhaust System 13B 6 PORT (using injection, has 6-port actuation and O2 sensor), 84-85
Comes with all hardware and an ACV block off plate.SKU: 16-MZTX-4230 -
EXHAUST SYSTEM DUAL, 12A DUAL PIPE 79-85
Racing Beat Dual Exhaust System, 12A Dual Pipe 79-85
SKU: 16422
You May Also Like:
-
EXHAUST HEADER 13B, 86-88 6 PORT DUAL PIPE
Racing Beat 13B Exhaust Header 86-88 With 6 Port Actuation and O2 Sensor Fitting Dual Pipe
SKU: 16128 -
EXHAUST CONVERTER GASKET, 93-95 MAIN FRONT & REAR
Exhaust Converter Gasket 93-95 Front and Rear of Main
SKU: 40-3050-RF36 Manufacturer SKU: RF36-40-305 -
EXHAUST HEADER 13B, 74-78 NO FLANGE EXCEPT PICK UP
Racing Beat 13B Exhaust Header, 74-78 No Flange. Will not work on the Pick Up
This rotary exhaust Header/Collector (less outlet flange) is ideal for RX-2, RX-3, RX-4, and COSMO (does not fit rotary pickup) custom exhaust installations. The flame-cut, .5-inch thick engine flange provides positive sealing and alignment. By integrating the collector with the header we reduce the effort and cost in completing the exhaust system. Engine-to-pipe gaskets are not included but are available separately. An Air Control and Check Valve Cover Plate is required when using this header with a stock intake system.
If the stock resonator is eliminated during installation of this unit, we strongly recommend selecting a Power Pulse Presilencer and installing it in place of the resonator to maintain a pleasant noise level and character.
SKU: 16007 -
Exhaust Down Pipe 86-92 Non-Turbo Coupes 2 1/2″
Exhaust Down Pipe 86-92 Non-Turbo Coupes 2 1/2″
This Down Pipe is available for custom applications in a 1986-91 RX-7 (excluding convertible) non-turbo application. This 2.5-inch down pipe fits either manual or automatic transmission equipped cars and eliminates the catalytic converter sections.
This down pipe bolts to the stock exhaust manifold, but the use of our presilencer (or a suitable replacement) is required to connect this assembly to the Y-pipe section. If you need to retain a catalytic converter in your exhaust system, you may find a suitable unit offered in the aftermarket. Although the replacement of your stock catalytic converters with a single aftermarket unit is technically NOT legal, this approach may suit your emissions needs. We suggest you contact your local emissions testing facility for more information. Gaskets sold separately.
SKU: S16206 -
MUFFLER UNIVERSAL, POWER PULSE 79-85 RACING BEAT
Racing Beat Universal Power Pulse Muffler, 79-85
In response to numerous requests from customers demanding a very low restriction“street capable” muffler, Racing Beat now offers the Universal Power Pulse PR-Extreme RX-7 Muffler with a 2.75″ OD internal perforated core design to meet the performance demands of high-horsepower ported rotary engines. The Power Pulse PR-Extreme RX-7 Muffler is compatible with all 1979-85 RX-7 muffler rear mounting positions and retains the factory stock appearance; this PR-Extreme RX-7 Muffler includes an inlet of 3″.
The Racing Beat Universal Power Pulse PR-Extreme RX-7 Muffler is manufactured by the same exhaust components manufacturer that has produced the “tried and proven” First Generation RX-7 Power Pulse mufflers (1979-80, 1981-82, and 1984-85) since the mid-1980s. Utilizing a heavy-walled canister shell and extremely durable heat and noise insulating materials, the Racing Beat Power Pulse PR-Extreme RX-7 Muffler is engineered for the high exhaust gas temperatures found in rotary engine applications.
The main body of the muffler canister measures 8 inches in diameter and 18 inches in length. The dual outlet tips are completely chrome-plated with straight-cut outlet.
Now may be the time to consider replacing the old rubber muffler hangers on your RX-7. New replacement hangers will ensure correct alignment of the RX-7 muffler canister and tip position in the bumper opening.
SKU: 16436 -
EXHAUST HEADER 12A, 81-83 RX7
Racing Beat 12A Exhaust Header, 81-83 RX7. Actual header not shown in photo – oxygen sensor fitting only included on 1984-85 RX-7 GSL-SE header.
This Racing Beat RX-7 Header is designed for a bolt-on installation, when used with the appropriate Racing Beat Power Pulse Presilencer in all 1981-83 RX-7s. The combination of this RX-7 header and the appropriate presilencer replaces the stock exhaust manifold and all catalytic converters for use on racing applications, along with any intermediate pieces of tubing.
The Racing Beat RX-7 header assembly is constructed with .120-inch wall, mandrel-bend, mild steel tubing for increased durability. The engine-to-header flange is laser-cut from 1/2-inch thick steel plate to ensure positive gas sealing. An outlet gasket is included. An engine-to-header gasket is available separately if needed.
SKU: 16010