EXHAUST PRE-SILENCER, 87-92 TURBO 3″
Racing Beat Exhaust Pre-Silencer, 87-92 Turbo 3″
| SKU: | 16425P |
EXHAUST PRE-SILENCER, 87-92 TURBO 3″
This REV TII Presilencer is a direct replacement for the presilencer section in the Racing Beat REV TII Complete Exhaust System. Positioned between the REV TII down pipe and Y-pipe sections, this stainless steel presilencer is intended as a bolt-on component ONLY if used with these REV TII Complete Exhaust System components.
Supplied with 3-inch OD inlet and outlet flanges, this presilencer section can also be used in a custom exhaust application. Gaskets are NOT supplied but can be purchased separately (2 each required).
$389.30
Related Products:
-
EXHAUST MUFFLER GASKET, USE WITH RACING BEAT 16425 SYSTEM
Exhaust Muffler Gasket, Use with Racing Beat 16425 System
SKU: 16339 -
EXHAUST PRE-SILENCER GASKET, RACING BEAT TURBO 3″
Racing Beat Exhaust Pre Silencer Gasket, Turbo 3″
Gasket for 16192 FlageSKU: 16340 -
EXHAUST SYSTEM, 86-92 TURBO
Racing Beat Exhaust System, 86-92 Turbo
1987-91 RX-7 TURBO REV II Complete High Performance Exhaust System – If you own a TURBO II RX-7 and you’ve found your way to this webpage, congratulations! Why? Because your search for an exhaust system for your car ends here. Simply put, this is the ultimate exhaust for any Turbo II RX-7!
The REV TII High Performance RX-7 Exhaust is legendary with FC3S owners. This RX-7 exhaust system includes a 3-inch OD REV TII Down Pipe from the turbo outlet that mates to a REV TII Presilencer section. The outlet of the presilencer connects to the inlet of the REV TII Y-Pipe which routes the exhaust gases down two 2.375-inch OD (60mm) pipes into a pair of left and right REV TII Power Pulse Mufflers. Once installed, this bolt-on exhaust system increases horsepower approximately 32% – that’s a 59 HP increase on a 1987 Turbo II RX-7!
The REV TII High Performance RX-7 Exhaust system reduces exhaust gas back-pressure significantly, thereby allowing the un-assisted turbo boost pressure to increase to 10-11 psi. (Note: A fuel cut controller device is required to prevent fuel cutoff to the rear rotor above the factory pre-set limit.)
This bolt-on system uses the stock mounting points for ease of installation. Each system is supplied with all necessary mounting hardware and gaskets. (The kit does not include turbo outlet gasket, if needed it can be ordered separately.) The down pipe section is provided with a position for the oxygen sensor.
SKU: 16425 -
EXHAUST HANGER, 86-92 @ “Y” PIPE
Exhaust Hanger at “Y” Pipe, 86-92
Go To Our FAQ for Exhaust Hangers to see the locations and part numbers of the hangers for your car.
SKU: 40-060B-N326 Manufacturer SKU: N326-40-060B -
EXHAUST HANGER, 86-92 BAND+ SLEEVE
Exhaust Hanger with Steel Band around it and a sleeve, 86-92
Go To Our FAQ for Exhaust Hangers to see the locations and part numbers of the hangers for your car.
SKU: 40-060B-N328 Manufacturer SKU: N328-40-060B -
You May Also Like:
-
-
-
-
MUFFLER UNIVERSAL, POWER PULSE 79-85 RACING BEAT
Racing Beat Universal Power Pulse Muffler, 79-85
In response to numerous requests from customers demanding a very low restriction“street capable” muffler, Racing Beat now offers the Universal Power Pulse PR-Extreme RX-7 Muffler with a 2.75″ OD internal perforated core design to meet the performance demands of high-horsepower ported rotary engines. The Power Pulse PR-Extreme RX-7 Muffler is compatible with all 1979-85 RX-7 muffler rear mounting positions and retains the factory stock appearance; this PR-Extreme RX-7 Muffler includes an inlet of 3″.
The Racing Beat Universal Power Pulse PR-Extreme RX-7 Muffler is manufactured by the same exhaust components manufacturer that has produced the “tried and proven” First Generation RX-7 Power Pulse mufflers (1979-80, 1981-82, and 1984-85) since the mid-1980s. Utilizing a heavy-walled canister shell and extremely durable heat and noise insulating materials, the Racing Beat Power Pulse PR-Extreme RX-7 Muffler is engineered for the high exhaust gas temperatures found in rotary engine applications.
The main body of the muffler canister measures 8 inches in diameter and 18 inches in length. The dual outlet tips are completely chrome-plated with straight-cut outlet.
Now may be the time to consider replacing the old rubber muffler hangers on your RX-7. New replacement hangers will ensure correct alignment of the RX-7 muffler canister and tip position in the bumper opening.
SKU: 16436 -
-
EXHAUST HEADER 13B, 89-92 6PORT DUAL PIPE
Racing Beat 13B Exhaust Header, 89-92 With 6 Port Actuation and O2 sensor fitting.
SKU: 16129