1981
Tools & Templates
-
CLUTCH DISC ALIGNMENT TOOL, ALL NON-TURBO 72-92
Clutch Disc Alignment Tool, All Non-turbo 72-92
Clutch alignment tools are needed whenever a clutch is installed. Damage to the clutch disc is almost assured if alignment is not correct.
SKU: 0033-05 -
COMPRESSION TESTER PRINTER, ADD-ON ONLY
Compression Tester Printer Add-on Only
Browse our Rotary Tools SectionSKU: TRPR -
COMPRESSION TESTER, TWISTED ROTORS
Compression Tester Tool, for Rotary Engines
Browse our Rotary Tools SectionSKU: TR01 -
COUNTERWEIGHT PULLER
Counterweight Puller
The Automatic Transmission Counter Balance Weight Puller Tool will remove any automatic transmission balance weight from its taper press fit on the eccentric shaft once the flywheel nut is loosened. This is the same balance weight used with all our lightweight flywheels. (Photo is shown with a Mazda counterweight, which is not included with this tool.)
SKU: 22003 -
DIGITAL TACH/ADVANCE TIMING LIGHT
We don’t sell this timing light but it is the one we recommend. Search for it on E-Bay or Amazon. This light is from Electronic Specialties Inc. The part number is ES-125
You need a timing light that has a setting for 2 Stroke engines.
SKU: ES-125 -
DOWEL PIN REMOVER TOOL
Dowel Pin Remover Tool
Tool makes pulling the dowels out of the rotor and side housings a piece of cake during engine dis-assembly.
SKU: 49-1290 -
-
-
ENGINE STAND, HEAD ONLY-ALL ROTARY
Engine Stand, Head Only-All Rotary
Please note: This is for the HEAD only – actual engine stand is not included (nor is the engine).Pipe size is 2 3/8 outside diameter – the most common size. PLEASE be sure your engine stand uses that size!!
SKU: MZTX-ENG-STAND Manufacturer SKU: MZTX-ENG-STAND -
FLYWHEEL NUT WRENCH
Racing Beat Flywheel Nut Wrench
Having the correct tool always makes the job seem easy, right? Although you probably won’t be using this tool much, it will certainly pay for itself even if you only use it once! The Flywheel Nut Wrench tool is used to remove or install the 54mm (2.125″) flywheel retaining nut. During re-assembly, this tool will allow you to accurately re-torque the nut to the required 350 foot-pounds This tool can be used with the engine in or out of the chassis.
SKU: 22000 -
-
FLYWHEEL SOCKET TOOL, 54MM IMPACT SOCKET
Flywheel Impact Socket Tool, 54mm, 3/4″ drive
SKU: 49-22009HD -
FLYWHEEL STOPPER TOOL
Racing Beat Flywheel Stopper Tool
The Flywheel Stopper Bar Tool is normally required whenever the rotary engine flywheel retaining nut is being removed or installed. The Racing Beat Stopper Bar bolts to either the stock flywheel, the Racing Beat Flywheel, or equivalent (except Tilton) and prevents the flywheel from rotating during the removal process. This is a GREAT timesaving tool, and can be used either in with the engine in the chassis, or while on an engine stand.
SKU: 22001 -
FLYWHEEL STOPPER TOOL, ALL Non-Turbo diameter flywheels
Flywheel Stopper Tool, All Non-Turbo diameter flywheels (Except RX-8’s)
Flywheel stopper makes getting the flywheel / counterweight nut off a LOT easier.
For flywheels 11 3/4″ diameter.SKU: 49-220NT Manufacturer SKU: 49-220NT -
HATCH SHOCK CLAMP, UNIVERSAL- ALL YEARS
Rear Hatch Shock Clamp, Universal- All Years
SKU: MAT-LSC-4487 -
PILOT BEARING REMOVER TOOL
Pilot Bearing Remover Tool
To remove the old pilot bearing the bearing MUST be gripped at its front end. Very few of the aftermarket pullers we tested were able to do this correctly. They often tended to destroy the bearing making removal even harder.
To use the tool simply insert the attachment into the bearing, being sure to get it to the end of the bearing, insert the tapered / threaded end of the slap hammer part and screw them together until the bearing is firmly gripped. Then just “slap hammer” it out. Should take less than a minute.
This tool prevents eccentric shaft damage when removing bearing.
This tool does fit other cars including Miata. We do not have a list of cars that it will work on. The RX pilot bearing/input shaft measures .588″. If your application also has a .588 shaft/bearing, this tool will work.SKU: 49-1285 -
PILOT BEARING TOOLS, INSTALLER & REMOVER
Mazda Rotary Engine Pilot Bearing Tools Remover and Installer Kit
SKU: KIT-PILOT-TOOLS -
PILOT REMOVER TOOL, END PIECE ONLY
End piece for OUR pilot bearing remover tool.
As far as we know it will not fit any other remover / slap hammer.
Thread is 1/2 x 13
SKU: 49-1285-END -
PORT TEMPLATE TOOL, J-BRIDGE INTAKE 4-PORT
PORT TEMPLATE TOOL, J-BRIDGE INTAKE 4-PORT
The Racing Beat Intake Port Templates allow you to undertake your own “J-bridge” port efforts on any 12A or 13B rotary engine (except 13B 6-port). These templates are traced from Racing Beat’s own master templates, which are the result of years of research and development. The actual port shapes are traced on thin sheets of aluminum which you must first cut out, testing your ability to use a die grinder effectively before attempting to port an expensive engine component. The finished template is held in place and the porting shape is then traced onto each housing. You must then use your own judgment to develop the port shape beyond the scribed line.
SKU: 22200
