FLYWHEEL STOPPER TOOL, ALL Non-Turbo diameter flywheels
Flywheel Stopper Tool, All Non-Turbo diameter flywheels (Except RX-8’s)
Flywheel stopper makes getting the flywheel / counterweight nut off a LOT easier.
For flywheels 11 3/4″ diameter.
| SKU: | 49-220NT |
| Manufacturer SKU: | 49-220NT |
FLYWHEEL STOPPER TOOL, ALL Non-Turbo diameter flywheels
$23.86
Related Products:
-
FLYWHEEL STOPPER TOOL
Racing Beat Flywheel Stopper Tool
The Flywheel Stopper Bar Tool is normally required whenever the rotary engine flywheel retaining nut is being removed or installed. The Racing Beat Stopper Bar bolts to either the stock flywheel, the Racing Beat Flywheel, or equivalent (except Tilton) and prevents the flywheel from rotating during the removal process. This is a GREAT timesaving tool, and can be used either in with the engine in the chassis, or while on an engine stand.
SKU: 22001 -
FLYWHEEL SOCKET TOOL, 54MM IMPACT SOCKET
Flywheel Impact Socket Tool, 54mm, 3/4″ drive
SKU: 49-22009HD -
-
SOCKET ADAPTER TOOL, 1/2″ FEMALE TO 3/4″ MALE
Socket Adapter Tool, 1/2″ Female To 3/4″ Male
3/4″ adapter to use 1/2″ drive. The flywheel nut is put on with over 300 foot-pounds of torque and this adapter CAN BREAK! BE CAREFUL!! (sorry – there is no warranty on it). Better to get a hold of a 3/4″ breaker bar that has a warranty from somebody.
(Just to let you know kind of worst case – We have had a few where we needed to use our 1″, 1200 foot pound, impact gun with our 1″ drive impact 54mm socket!)
SKU: 49-22008 -
FLYWHEEL STOPPER TOOL, TURBO, AUTO TRANS AND RX8
Flywheel Stopper Tool, Turbo, Automatic Transmission And RX8 Manual
SKU: 49-220TB Manufacturer SKU: 49-220TB -
FLYWHEEL NUT WRENCH
Racing Beat Flywheel Nut Wrench
Having the correct tool always makes the job seem easy, right? Although you probably won’t be using this tool much, it will certainly pay for itself even if you only use it once! The Flywheel Nut Wrench tool is used to remove or install the 54mm (2.125″) flywheel retaining nut. During re-assembly, this tool will allow you to accurately re-torque the nut to the required 350 foot-pounds This tool can be used with the engine in or out of the chassis.
SKU: 22000
You May Also Like:
-
TRANSMISSION MOUNT REAR 74-85 COMPETITION–NLA–
Sorry, this item has been discontinued by Mazda
Rear Transmission Mount, 74-85 All Manual Transimission, Competition
SKU: 39-3400-4352 Manufacturer SKU: 4352-39-340 -
-
CLUTCH COVER, ALL ROTARY -82
Clutch Cover, All Rotary up to 82
Stock/Original EquipmentSKU: 16-410A-1769 Manufacturer SKU: 1769-16-410A -
CLUTCH FORK BOOT 86-92 TURBO
Clutch Fork Boot 86-92 Turbo
SKU: 16-2140-N302 Manufacturer SKU: N302-16-214 -
CLUTCH DISC RACE, ALL ROTARY -82
Racing Beat Race Clutch Disc, All Rotary up to 82, 4 puck
The 4-Puck 215mm Race Clutch Disc is designed for drag and road race use with all 1971-82 12A & 13B Applications (except Rotary Pick-Up). The disc incorporates four (4) sintered copper pucks and a rigid hub for quick, positive engagement, greater fatigue resistance, and improved heat dissipation. The sharpened engagement/disengagement characteristics of this disc require careful driver attention – this disc is not intended for street use.
Time Saving Tip: We strongly recommend replacing the throw-out bearing during any clutch work to ensure trouble free performance. Also, we recommend replacing the transmission front and rear seal kit when re-installing the transmission to reduce the possibility of leakage.
Safety Note: None of the Racing Beat, Exedy, Mazda OE, or any aftermarket flywheel or clutch replacement components should ever be allowed to exceed 10,500 RPM under any condition. You must use an engine RPM-limiter to prevent excessive RPM. If your engine is capable of exceeding 8,500 RPM you must install a transmission scatter shield or ballistic blanket. Failure to implement the above may result in serious injury or even death.
Actual disc not shown in photo.
SKU: 12521 -
CLUTCH KIT, 79-82
Clutch Kit, 79-82
Stock/Original EquipmentOEM Street Clutch Kit
Includes Disc, Pressure Plate, T/O Bearing, Pilot Bearing and seal, and Alignment ToolWe open every Exedy Kit to make sure that the correct Pilot Bearing and seal are included, due to Exedy rarely includes the pilot seal and sometimes has the incorrect bearing.
SKU: 07020 Manufacturer SKU: 07020