ENGINE STAND, HEAD ONLY-ALL ROTARY
Engine Stand, Head Only-All Rotary
Please note: This is for the HEAD only – actual engine stand is not included (nor is the engine).
Pipe size is 2 3/8 outside diameter – the most common size. PLEASE be sure your engine stand uses that size!!
| SKU: | MZTX-ENG-STAND |
| Manufacturer SKU: | MZTX-ENG-STAND |
ENGINE STAND, HEAD ONLY-ALL ROTARY
Made in the USA
$79.95
Related Products:
-
FLYWHEEL NUT WRENCH
Racing Beat Flywheel Nut Wrench
Having the correct tool always makes the job seem easy, right? Although you probably won’t be using this tool much, it will certainly pay for itself even if you only use it once! The Flywheel Nut Wrench tool is used to remove or install the 54mm (2.125″) flywheel retaining nut. During re-assembly, this tool will allow you to accurately re-torque the nut to the required 350 foot-pounds This tool can be used with the engine in or out of the chassis.
SKU: 22000 -
FLYWHEEL SOCKET TOOL, 54MM IMPACT SOCKET
Flywheel Impact Socket Tool, 54mm, 3/4″ drive
SKU: 49-22009HD -
FLYWHEEL STOPPER TOOL
Racing Beat Flywheel Stopper Tool
The Flywheel Stopper Bar Tool is normally required whenever the rotary engine flywheel retaining nut is being removed or installed. The Racing Beat Stopper Bar bolts to either the stock flywheel, the Racing Beat Flywheel, or equivalent (except Tilton) and prevents the flywheel from rotating during the removal process. This is a GREAT timesaving tool, and can be used either in with the engine in the chassis, or while on an engine stand.
SKU: 22001 -
-
SOCKET ADAPTER TOOL, 1/2″ FEMALE TO 3/4″ MALE
Socket Adapter Tool, 1/2″ Female To 3/4″ Male
3/4″ adapter to use 1/2″ drive. The flywheel nut is put on with over 300 foot-pounds of torque and this adapter CAN BREAK! BE CAREFUL!! (sorry – there is no warranty on it). Better to get a hold of a 3/4″ breaker bar that has a warranty from somebody.
(Just to let you know kind of worst case – We have had a few where we needed to use our 1″, 1200 foot pound, impact gun with our 1″ drive impact 54mm socket!)
SKU: 49-22008 -
COUNTERWEIGHT PULLER
Counterweight Puller
The Automatic Transmission Counter Balance Weight Puller Tool will remove any automatic transmission balance weight from its taper press fit on the eccentric shaft once the flywheel nut is loosened. This is the same balance weight used with all our lightweight flywheels. (Photo is shown with a Mazda counterweight, which is not included with this tool.)
SKU: 22003
You May Also Like:
-
PORT TEMPLATE TOOL, J-BRIDGE INTAKE 4-PORT
PORT TEMPLATE TOOL, J-BRIDGE INTAKE 4-PORT
The Racing Beat Intake Port Templates allow you to undertake your own “J-bridge” port efforts on any 12A or 13B rotary engine (except 13B 6-port). These templates are traced from Racing Beat’s own master templates, which are the result of years of research and development. The actual port shapes are traced on thin sheets of aluminum which you must first cut out, testing your ability to use a die grinder effectively before attempting to port an expensive engine component. The finished template is held in place and the porting shape is then traced onto each housing. You must then use your own judgment to develop the port shape beyond the scribed line.
SKU: 22200 -
COMPRESSION TESTER, TWISTED ROTORS
Compression Tester Tool, for Rotary Engines
Browse our Rotary Tools SectionSKU: TR01 -
FLYWHEEL STOPPER TOOL, ALL Non-Turbo diameter flywheels
Flywheel Stopper Tool, All Non-Turbo diameter flywheels (Except RX-8’s)
Flywheel stopper makes getting the flywheel / counterweight nut off a LOT easier.
For flywheels 11 3/4″ diameter.SKU: 49-220NT Manufacturer SKU: 49-220NT -
HATCH SHOCK CLAMP, UNIVERSAL- ALL YEARS
Rear Hatch Shock Clamp, Universal- All Years
SKU: MAT-LSC-4487 -
PORT TEMPLATE TOOL, PORTING BLANK
PORT TEMPLATE TOOL, PORTING BLANK
We no longer make this blank Intake Template.
SKU: 49-222BLANK
