DOWEL PULLER, COMPACT RACING BEAT
Racing Beat Compact Dowel Puller
| SKU: | 22004 |
| Manufacturer SKU: | 22004 |
DOWEL PULLER, COMPACT RACING BEAT
The Tubular Dowel Puller Tool allows easy removal of the four tubular dowels used to align the engine housings. In some instances, these dowels can be removed by hand, but this inexpensive tool facilitates the task.
$21.83
Related Products:
-
-
DOWEL PIN FRONT & REAR STATIONARY GEAR TO HOUSING
Front and Rear Stationary Gear to Housing Dowel Pin
SKU: 10-2030-0839 Manufacturer SKU: 0839-10-203 -
DOWEL PIN 93-95 AUTO, REAR HOUSING TO STARTER
Rear Housing to Starter Dowel Pin 93-95 Automatic Trans
SKU: 41-2080-9923 Manufacturer SKU: 9923-41-208 -
ENGINE DOWEL PIN, 13B ALL (INCLUDING RX8)
Engine Dowel Pin, 13B All (Including RX8)
SKU: 10-1110-1757 Manufacturer SKU: 1757-10-111 -
DOWEL PIN SHORT, FRONT COVER & BELLHOUSING
Front Cover and Bellhousing Short Dowel Pin
SKU: 10-3090-1757 Manufacturer SKU: 1757-10-309 -
DOWEL PIN REMOVER TOOL
Dowel Pin Remover Tool
Tool makes pulling the dowels out of the rotor and side housings a piece of cake during engine dis-assembly.
SKU: 49-1290
You May Also Like:
-
PILOT BEARING REMOVER TOOL
Pilot Bearing Remover Tool
To remove the old pilot bearing the bearing MUST be gripped at its front end. Very few of the aftermarket pullers we tested were able to do this correctly. They often tended to destroy the bearing making removal even harder.
To use the tool simply insert the attachment into the bearing, being sure to get it to the end of the bearing, insert the tapered / threaded end of the slap hammer part and screw them together until the bearing is firmly gripped. Then just “slap hammer” it out. Should take less than a minute.
This tool prevents eccentric shaft damage when removing bearing.
This tool does fit other cars including Miata. We do not have a list of cars that it will work on. The RX pilot bearing/input shaft measures .588″. If your application also has a .588 shaft/bearing, this tool will work.SKU: 49-1285 -
CLUTCH DISC ALIGNMENT TOOL, ALL NON-TURBO 72-92
Clutch Disc Alignment Tool, All Non-turbo 72-92
Clutch alignment tools are needed whenever a clutch is installed. Damage to the clutch disc is almost assured if alignment is not correct.
SKU: 0033-05 -
FLYWHEEL STOPPER TOOL
Racing Beat Flywheel Stopper Tool
The Flywheel Stopper Bar Tool is normally required whenever the rotary engine flywheel retaining nut is being removed or installed. The Racing Beat Stopper Bar bolts to either the stock flywheel, the Racing Beat Flywheel, or equivalent (except Tilton) and prevents the flywheel from rotating during the removal process. This is a GREAT timesaving tool, and can be used either in with the engine in the chassis, or while on an engine stand.
SKU: 22001 -
PILOT REMOVER TOOL, END PIECE ONLY
End piece for OUR pilot bearing remover tool.
As far as we know it will not fit any other remover / slap hammer.
Thread is 1/2 x 13
SKU: 49-1285-END -
COUNTERWEIGHT PULLER
Counterweight Puller
The Automatic Transmission Counter Balance Weight Puller Tool will remove any automatic transmission balance weight from its taper press fit on the eccentric shaft once the flywheel nut is loosened. This is the same balance weight used with all our lightweight flywheels. (Photo is shown with a Mazda counterweight, which is not included with this tool.)
SKU: 22003 -
FLYWHEEL STOPPER TOOL, TURBO, AUTO TRANS AND RX8
Flywheel Stopper Tool, Turbo, Automatic Transmission And RX8 Manual
SKU: 49-220TB Manufacturer SKU: 49-220TB