EXHAUST SPLIT AIR PIPE, S5 TURBO —NLA—
EXHAUST SPLIT AIR PIPE, S5 TURBO
Sorry, this item has been discontinued by Mazda.
| SKU: | 20-840A-N370 |
| Manufacturer SKU: | N370-20-840A |
EXHAUST SPLIT AIR PIPE, S5 TURBO
$0.00
Related Products:
-
-
EXHAUST SYSTEM, 86-92 TURBO
Racing Beat Exhaust System, 86-92 Turbo
1987-91 RX-7 TURBO REV II Complete High Performance Exhaust System – If you own a TURBO II RX-7 and you’ve found your way to this webpage, congratulations! Why? Because your search for an exhaust system for your car ends here. Simply put, this is the ultimate exhaust for any Turbo II RX-7!
The REV TII High Performance RX-7 Exhaust is legendary with FC3S owners. This RX-7 exhaust system includes a 3-inch OD REV TII Down Pipe from the turbo outlet that mates to a REV TII Presilencer section. The outlet of the presilencer connects to the inlet of the REV TII Y-Pipe which routes the exhaust gases down two 2.375-inch OD (60mm) pipes into a pair of left and right REV TII Power Pulse Mufflers. Once installed, this bolt-on exhaust system increases horsepower approximately 32% – that’s a 59 HP increase on a 1987 Turbo II RX-7!
The REV TII High Performance RX-7 Exhaust system reduces exhaust gas back-pressure significantly, thereby allowing the un-assisted turbo boost pressure to increase to 10-11 psi. (Note: A fuel cut controller device is required to prevent fuel cutoff to the rear rotor above the factory pre-set limit.)
This bolt-on system uses the stock mounting points for ease of installation. Each system is supplied with all necessary mounting hardware and gaskets. (The kit does not include turbo outlet gasket, if needed it can be ordered separately.) The down pipe section is provided with a position for the oxygen sensor.
SKU: 16425 -
SPLIT AIR EXHAUST GASKET, 81-95 PIPE TO CAT
Split Air Exhaust Gasket, 81-95 Split Air Pipe To Cat
SKU: 40-3750-YJZ4 Manufacturer SKU: YJZ4-40-375 -
EXHAUST HANGER, 86-92 BAND+ SLEEVE
Exhaust Hanger with Steel Band around it and a sleeve, 86-92
Go To Our FAQ for Exhaust Hangers to see the locations and part numbers of the hangers for your car.
SKU: 40-060B-N328 Manufacturer SKU: N328-40-060B -
SPLIT AIR PIPE TO MANIFOLD GASKET 86-95 TURBO
86-95 Turbo Split Air Pipe To Manifold Gasket
SKU: 13-164A-N318 Manufacturer SKU: N318-13-164A -
EXHAUST HANGER, 86-92 @ “Y” PIPE
Exhaust Hanger at “Y” Pipe, 86-92
Go To Our FAQ for Exhaust Hangers to see the locations and part numbers of the hangers for your car.
SKU: 40-060B-N326 Manufacturer SKU: N326-40-060B
You May Also Like:
-
SPLIT AIR EXHAUST GASKET, —NLA— 79-80 HEAT EXCHANGER FRONT & REAR
Split Air Exhaust Gasket, 79-80 Split Air Pipe To Catalytic Converter
Heat Exchanger Front and RearSorry, this item has been discontinued by Mazda
SKU: 13-135B-8527 Manufacturer SKU: 8527-13-135B -
-
-
-
EXHAUST CONVERTER GASKET 93-95 MAIN FRONT & REAR
Exhaust Converter Gasket 93-95 Front and Rear of Main
SKU: 40-3050-RF36 Manufacturer SKU: RF36-40-305 -
EXHAUST PRE-SILENCER WITH DOWN PIPE, 88 CONVERTIBLE MANUAL
Racing Beat Exhaust Pre-Silencer with Down Pipe, 88 Convertible Manual Transmission Non-Turbo
Down Pipe with Presilencer – 1988 RX-7 Convertible Non-Turbo (w/Manual Transmission) – The 1986-92 13B 6-port engines, in stock form with the factory fuel injection, produces similar power gains with either our Header/Presilencer combo or our RX-7 Down Pipe/Presilencer combination. If you have no intentions of installing RB’s Holley intake System (or any other aftermarket carb set-up), we recommend the use of the down pipe/Presilencer combo since it offers a slightly quieter exhaust note, is easier to install and less costly. If you are intending to upgrade the intake or fuel injection system, the Header/Presilencer combo offers the greatest performance potential.
The 1988 RX-7 Convertible (w/ Manual Transmission) Down Pipe/Presilencer combination incorporates a 2.5-inch O.D. Down Pipe and our perforated stainless steel core and stainless steel wool-packed Presilencer to boost power approximately 13% – an 18 horsepower increase on a 1987 RX 7- and maintain a comfortable exhaust noise level during full power driving.
The replacement pipe connects to the factory exhaust manifold, and the presilencer connects to the factory Y-pipe, replacing all catalytic converters and intermediate tubing. (The downpipe cannot be used as a “bolt-up” component to replace just the catalytic converters.)
The Racing Beat presilencer is equipped with an exhaust back-pressure tube for correct operation of the 6-port actuators. Installation of this requires the removal of the air control and check valve and the air pump. This kit includes all necessary mounting hardware, air control & check valve cover plate, and gaskets (1 Back Pressure Pick-up and 3 Replacement Pipe-to-Presilencer gaskets).
SKU: 16209