EXHAUST TIP, 86-92 TURBO—NLA—

Related Products:

• 

  EXHAUST HANGER, 2 SLEEVES

  

  Exhaust Hanger, 2 Sleeves

  Go To Our FAQ for Exhaust Hangers to see the locations and part numbers of the hangers for your car.

  SKU:	40-1600-1114
  Manufacturer SKU:	1114-40-160

  $30.14
  Add to cart
• 

  EXHAUST HANGER, 86-92 @ “Y” PIPE

  

  Exhaust Hanger at “Y” Pipe, 86-92

  Go To Our FAQ for Exhaust Hangers to see the locations and part numbers of the hangers for your car.

  SKU:	40-060B-N326
  Manufacturer SKU:	N326-40-060B

  $33.25
  Add to cart
• 

  EXHAUST HANGER, DONUT

  

  Exhaust Hanger Donut

   

  SKU:	40-0610-1114
  Manufacturer SKU:	1114-40-061

  $15.35
  Add to cart
• 

  EXHAUST SYSTEM, 86-92 TURBO

  Racing Beat Exhaust System, 86-92 Turbo

  1987-91 RX-7 TURBO REV II Complete High Performance Exhaust System – If you own a TURBO II RX-7 and you’ve found your way to this webpage, congratulations! Why? Because your search for an exhaust system for your car ends here. Simply put, this is the ultimate exhaust for any Turbo II RX-7!

  The REV TII High Performance RX-7 Exhaust is legendary with FC3S owners.  This RX-7 exhaust system includes a 3-inch OD REV TII Down Pipe from the turbo outlet that mates to a REV TII Presilencer section. The outlet of the presilencer connects to the inlet of the REV TII Y-Pipe which routes the exhaust gases down two 2.375-inch OD (60mm) pipes into a pair of left and right REV TII Power Pulse Mufflers. Once installed, this bolt-on exhaust system increases horsepower approximately 32% – that’s a 59 HP increase on a 1987 Turbo II RX-7!

  The REV TII High Performance RX-7 Exhaust system reduces exhaust gas back-pressure significantly, thereby allowing the un-assisted turbo boost pressure to increase to 10-11 psi. (Note: A fuel cut controller device is required to prevent fuel cutoff to the rear rotor above the factory pre-set limit.)

  This bolt-on system uses the stock mounting points for ease of installation. Each system is supplied with all necessary mounting hardware and gaskets. (The kit does not include turbo outlet gasket, if needed it can be ordered separately.) The down pipe section is provided with a position for the oxygen sensor.

  SKU:

  16425

  $1,473.50
  Add to cart
• 

  EXHAUST HANGER, 86-92 BAND+ SLEEVE

  

  Exhaust Hanger with Steel Band around it and a sleeve, 86-92

  Go To Our FAQ for Exhaust Hangers to see the locations and part numbers of the hangers for your car.

  SKU:	40-060B-N328
  Manufacturer SKU:	N328-40-060B

  $32.66
  Add to cart
• 

  Exhaust Down Pipe for 87-92 TURBO 2 1/2″

  This Down Pipe is available for custom applications in a 1987-91 RX-7 Turbo II application.

   This 2.5-inch down pipe fits either manual or automatic transmission equipped cars and eliminates the catalytic converter sections.

  This down pipe bolts to the stock turbo, but the use of our presilencer (or a suitable replacement) is required to connect this assembly to the Y-pipe section. If you need to retain a catalytic converter in your exhaust system, you may find a suitable unit offered in the aftermarket. Although the replacement of your stock catalytic converters with a single aftermarket unit is technically NOT legal, this approach may suit your emissions needs. We suggest you contact your local emissions testing facility for more information. Gaskets sold separately.

  .

  SKU:

  S16207

  $204.44
  Add to cart