EXHAUST HEADER 12A, 79-85 RX7 DUAL OUTLET
EXHAUST HEADER 12A, 79-85 RX7 DUAL OUTLET

EXHAUST HEADER 12A, 79-85 RX7 DUAL OUTLET

Racing Beat 12A Exhaust Header, 79-85 RX7 Dual Outlet

SKU: 16125

EXHAUST HEADER 12A, 79-85 RX7 DUAL OUTLET

Racing Beat’s Road Race Header is the first step in building a serious racing exhaust system. The engine-to-pipe flange is laser cut from 7/16″ thick flat steel. Like all of the headers they manufacture, the Road Racing Header is constructed with 2″ OD mild steel tubing, .125″ wall thickness, and mandrel-bent tubing throughout.

Outlet flange gaskets, bolts, and nuts are included. An engine-to-header gasket is not included, but is available separately. An Air Control and Check Valve Cover Plate (1979-80 or 1981-92) is required when using this header with a stock intake system. The Road Race Header can also be used as the basis for a custom streetable exhaust system in any car from 1971-92 which allows simple swapping between street and race exhaust systems.

These headers can used as a bolt-on component with the Street Port Center Section Pipe (1979-85 12A & 13B – except GSL-SE) or (1984-85 GSL-SE) that we offer for these model years.

$375.95

Related Products:

You May Also Like:

  • EXHAUST PRE-SILENCER, 81-83

    EXHAUST PRE-SILENCER, 81-83

    Racing Beat Exhaust Pre-Silencer, 71-78, 81-83

    The Racing Beat Power Pulse Presilencer for the 1971-78 & 81-83 RX-7 is designed to be used with our wide selection of RX-7 Streetable Headers to complete a bolt-on configuration. These Power Pulse Presilencers are ideal for those individuals wanting to fabricate custom exhaust systems incorporating either long or short primary exhaust systems.

    The Power Pulse Presilencer improves the character of the exhaust noise, dramatically reducing the inherent, obnoxious metallic high frequency noise with virtually no power loss. Constructed with a high temperature, 2-inch I.D. perforated core of 304 stainless steel wrapped with high-temperature stainless steel wool, the Power Pulse Presilencer measures 20 inches in length with a 4-inch outside diameter. The mounting studs are 12mm both front and rear.

    SKU: 16400
    $291.06
    Add to cart
  • EXHAUST HEADER 13B, 74-78 NO FLANGE EX PICK UP

    EXHAUST HEADER 13B, 74-78 NO FLANGE EXCEPT PICK UP

    Racing Beat 13B Exhaust Header, 74-78 No Flange. Will not work on the Pick Up

    This rotary exhaust Header/Collector (less outlet flange) is ideal for RX-2, RX-3, RX-4, and COSMO (does not fit rotary pickup) custom exhaust installations. The flame-cut, .5-inch thick engine flange provides positive sealing and alignment. By integrating the collector with the header we reduce the effort and cost in completing the exhaust system. Engine-to-pipe gaskets are not included but are available separately. An Air Control and Check Valve Cover Plate is required when using this header with a stock intake system. 

    If the stock resonator is eliminated during installation of this unit, we strongly recommend selecting a Power Pulse Presilencer and installing it in place of the resonator to maintain a pleasant noise level and character.

    SKU: 16007
    $389.30
    Add to cart
  • EXHAUST HEADER 13B, 74-78 DUAL OUTLET

    EXHAUST HEADER 13B, 74-78 DUAL OUTLET

    Racing Beat Exhaust Header 13B, 74-78 Dual Outlet

    SKU: 16003
    $375.95
    Add to cart
  • EXHAUST HEADER 12A, 79-80 RX7

    EXHAUST HEADER 12A, 79-80 RX7

    Racing Beat 12A Exhaust Header, 79-80 RX7

    SKU: 16008
    $389.30
    Add to cart