EXHAUST SYSTEM DUAL, 12A DUAL PIPE 79-85
Racing Beat Dual Exhaust System, 12A Dual Pipe 79-85
| SKU: | 16422 |
EXHAUST SYSTEM DUAL, 12A DUAL PIPE 79-85
Our Racing Beat-designed, “Long Primary” Street Port Complete RX-7 Exhaust System is designed for any 1979-85 RX-7 with a 12A street-ported engine. Designed specifically to optimize the performance benefit of a ported rotary engine, this RX-7 exhaust system will provide the maximum power output possible from an aftermarket RX-7 exhaust system. While louder than the stock system, the dual resonated center section offers maximum exhaust gas flow and scavenging while reducing sound output to a modest level.
Offered as a packaged set, this kit consists of a Road Race Header, the Street Port Center Section, and a high flow Power Pulse Main muffler.
The Long Primary system typically adds 5% or more horsepower over a standard Short Primary system on a street ported engine, especially at higher RPMs. This system can also be used on non-ported engines with good results. It is strictly bolt-on, with no welding required. These complete “bolt-on” systems come complete with all required mounting hardware and gaskets. Since this is intended for racing applications, there is no provision for an oxygen sensor on this system.
$1,449.24
Related Products:
-
EXHAUST HANGER, 2 SLEEVES
Exhaust Hanger, 2 Sleeves
Go To Our FAQ for Exhaust Hangers to see the locations and part numbers of the hangers for your car.
SKU: 40-1600-1114 Manufacturer SKU: 1114-40-160 -
EXHAUST CENTER SECTION, 79-85 RACING BEAT 4 PORT/6 PORT
Racing Beat Exhaust Center Section, 79-85 4 Port/6 Port
SKU: 16398 -
EXHAUST HEADER 12A, 79-85 RX7 DUAL OUTLET
Racing Beat 12A Exhaust Header, 79-85 RX7 Dual Outlet
SKU: 16125 -
EXHAUST MANIFOLD GASKET, 12A 81-85
Exhaust Manifold Gasket, 12A 81-85
SKU: 13-889B-1480 Manufacturer SKU: 1480-13-889B -
-
EXHAUST SYSTEM SINGLE, 84-85 12A AUTOMATIC TRANSMISSION
Racing Beat Single Exhaust System, 84-85 12A with Automatic Transmission
Racing Beat offers a complete RX-7 high-performance exhaust system for the 1984-85 12A RX-7 (w/automatic transmission) which includes our Header/Collector, a Power-Pulse Presilencer, and our legendary Power Pulse main muffler. These components attach to all stock mounting points, and include all necessary gaskets and hardware. The only component not included is the factory connecting pipe that mounts just ahead of the main muffler. There is no horsepower to be gained by replacing this pipe with a larger diameter assembly. If your factory connecting pipe needs replacing, we suggest you contact your local Mazda dealer or muffler shop.
These exhaust systems offer excellent horsepower gains when you require a muffled exhaust system for your stock-ported engine. The actual horsepower increase depends on which year/model stock RX-7 exhaust system you are comparing to, but a 22% increase at 7000 rpm is typical. Thanks to the combined efforts of the Power-Pulse Presilencer and the Power Pulse Main muffler, the exhaust noise is only slightly higher than stock, with a very low, pleasant character.
SKU: 16419
You May Also Like:
-
EXHAUST PRE-SILENCER WITH DOWN PIPE, 88 CONVERTIBLE MANUAL
Racing Beat Exhaust Pre-Silencer with Down Pipe, 88 Convertible Manual Transmission Non-Turbo
Down Pipe with Presilencer – 1988 RX-7 Convertible Non-Turbo (w/Manual Transmission) – The 1986-92 13B 6-port engines, in stock form with the factory fuel injection, produces similar power gains with either our Header/Presilencer combo or our RX-7 Down Pipe/Presilencer combination. If you have no intentions of installing RB’s Holley intake System (or any other aftermarket carb set-up), we recommend the use of the down pipe/Presilencer combo since it offers a slightly quieter exhaust note, is easier to install and less costly. If you are intending to upgrade the intake or fuel injection system, the Header/Presilencer combo offers the greatest performance potential.
The 1988 RX-7 Convertible (w/ Manual Transmission) Down Pipe/Presilencer combination incorporates a 2.5-inch O.D. Down Pipe and our perforated stainless steel core and stainless steel wool-packed Presilencer to boost power approximately 13% – an 18 horsepower increase on a 1987 RX 7- and maintain a comfortable exhaust noise level during full power driving.
The replacement pipe connects to the factory exhaust manifold, and the presilencer connects to the factory Y-pipe, replacing all catalytic converters and intermediate tubing. (The downpipe cannot be used as a “bolt-up” component to replace just the catalytic converters.)
The Racing Beat presilencer is equipped with an exhaust back-pressure tube for correct operation of the 6-port actuators. Installation of this requires the removal of the air control and check valve and the air pump. This kit includes all necessary mounting hardware, air control & check valve cover plate, and gaskets (1 Back Pressure Pick-up and 3 Replacement Pipe-to-Presilencer gaskets).
SKU: 16209 -
EXHAUST HEADER 13B, 74-78 NO FLANGE EXCEPT PICK UP
Racing Beat 13B Exhaust Header, 74-78 No Flange. Will not work on the Pick Up
This rotary exhaust Header/Collector (less outlet flange) is ideal for RX-2, RX-3, RX-4, and COSMO (does not fit rotary pickup) custom exhaust installations. The flame-cut, .5-inch thick engine flange provides positive sealing and alignment. By integrating the collector with the header we reduce the effort and cost in completing the exhaust system. Engine-to-pipe gaskets are not included but are available separately. An Air Control and Check Valve Cover Plate is required when using this header with a stock intake system.
If the stock resonator is eliminated during installation of this unit, we strongly recommend selecting a Power Pulse Presilencer and installing it in place of the resonator to maintain a pleasant noise level and character.
SKU: 16007 -
-
EXHAUST HEADER 13B, 79-92 4&6-PORT DUAL OUTLET
Racing Beat 13B Exhaust Header, 79-92 4&6-PORT DUAL OUTLET
SKU: 16127 Manufacturer SKU: 16127 -
-
