2011
General Hardware
-
DRY SUMP ADAPTER #1, ALUMINUM AN -12
Aluminum AN Dry Sump Adapter #1, -12
SKU: 14-R960-ZR03 Manufacturer SKU: ZR03-14-R96 -
DRY SUMP ADAPTER #2, ALUMINUM AN -16
Aluminum Dry Sump Adapter #2, AN -16
SKU: 14-R980-ZR03 Manufacturer SKU: ZR03-14-R98 -
FLYWHEEL HARDWARE, STEEL 74-92,TURBO, RACE
Steel Flywheel Hardware Kit, 74-92, Turbo, Race
Flywheel to Counterweight Bolt SetSKU: 95179 -
FREEZE PLUG LARGE, ALL FRONT & REAR HOUSING
1 3/16″ diameter Mazda OEM freeze plug for the larger holes front and rear side housings.
( uses 6-7 depending on year)
SKU: 63-0000-9930 Manufacturer SKU: 9930-63-000 -
FREEZE PLUG SMALL, FRONT HOUSING
Freeze Plug Small (3/4″ Diameter), Front Housing
(for front side housing, uses 1)SKU: 62-0000-9930 Manufacturer SKU: 9930-62-000 -
FUEL DOOR BUMP STOP, 81-85 RX7, 93-95 RX7, & 04-11 RX8
Fuel Door Bump Stop (Two per Vehicle)
Fits 81-85 RX7
93-95 RX7
04-11 RX8SKU: 70-4910-0187 Manufacturer SKU: 0187-70-491 -
HYLOMAR TUBE, 1.5 OZ
HYLOMAR TUBE, 1.5 OZ
Best chemical we have found for water seal O-rings. Brush it on with a trimmed down “acid” brush – in the water seal grooves and then on the seals after you have placed them into the grooves. Stays tacky for a LONG time.
One tube will do one engine easily.
SKU: HYLOMAR -
LOWER STARTER BOLT AUTOMATIC 04-11 RX8
LOWER STARTER BOLT AUTOMATIC 04-11 RX8
SKU: 60-8350-9979 Manufacturer SKU: 9979-60-835 -
OIL HOSE FITTING, 93-95 & 04-11, END WITH CLIP
Oil Hose Fitting, 93-95 & 04-11, End With Clip
SKU: 14-850A-N3G1 Manufacturer SKU: N3G1-14-850A -
OIL HOSE RETAINING CLIP, SUPERSEDED USE N3G1-14-850A
OIL HOSE RETAINING CLIP, SUPERSEDED USE N3G1-14-850A
This item has been superseded. Now use N3G1-14-850A
SKU: 14-6220-N3A1 Manufacturer SKU: N3A1-14-622 -
Plug Oil Injector Hole (rotor housings + intake manifold)
Plug for plugging oil injector holes (rotor housings + intake manifold) when they are not being used. Sold EACH, you typically need 2 or 4 depending what you are doing. Fits all oil injector holes from 84-11. Supplied with sealing washer. Uses 3/16 allen wrench.
SKU: 19-064A-FT01-RT Manufacturer SKU: FT01-19-064A-RT -
POWERPLANT FRAME TAPER BOLT 93-11
Powerplant Frame Taper Bolt 93-11
SKU: 39-0660-FD01 Manufacturer SKU: FD01-39-066 -
RIVET PLASTIC 86-ON, PUSH BUTTON TYPE -NLA-
This item has been discontinued by Mazda
Plastic Push Button Type Rivet, 86-On
SKU: 56-81X0-FB01 Manufacturer SKU: FB01-56-81X -
RIVET PLASTIC, FAN SHROUD LOWER
Plastic Rivet, Fan Shroud Lower
SKU: 40-6580-9926 Manufacturer SKU: 9926-40-658 -
SCREW BRAKE ROTOR, ALL YEARS (EACH)
Brake Rotor Screw, All Years, Phillips Flat Head, Counter Sunk
Sold individuallySKU: 10-8200-9983 Manufacturer SKU: 9983-10-820 -
UPPER STARTER BOLT 04-11 RX8
UPPER STARTER BOLT 04-11 RX8
SKU: 01-0130-9980 Manufacturer SKU: 9980-01-0130 -
UPPER STARTER NUT 04-11 RX8
UPPER STARTER BOLT NUT 04-11 RX8
SKU: 01-0000-9994 Manufacturer SKU: 9994-01-000 -
WEBER IDLE SPEED SCREW
Weber Idle Speed Screw
Spring is not included. It is 47600.007Browse our Weber Carbs, Manifolds and Parts section
SKU: 64625.012 -
WEBER INLET FITTING for 8mm (5/16″) push on hose
Weber 12mm Inlet Fitting for a regular 5/16″ rubber hose.
All Weber IDA carbs come with a useless banjo fitting we have never figured out how to use (unless you tap it 1/8-pipe and use a “barb” fitting). This will replace the stock inlet fitting with a hose nipple that you can push on and clamp regular fuel hose to. This is the stock fuel hose size for all Mazda RX cars.
Click Here for a Weber 48IDA Suggested Parts List
Browse our Weber Carbs, Manifolds and Parts section
SKU: 99301.380 Manufacturer SKU: 99301.380 -
WEBER INLET FITTING, AN -6 TO WEBER 12MM
-6 To Weber 12mm Inlet Fitting
All Weber IDA carbs come with a useless banjo fitting we have never figured out how to use (unless you tap it 1/8-pipe and use a “barb” fitting). This will replace the stock inlet fitting with -6AN so you can use braided hose.
The 12mm Stat-O-Seal is strongly recommended for this fitting — it is at: WEBER INLET SEAL, STAT-O-SEAL FOR 12MM
We also have a 90° fitting for 8mm / 5/16″ push on hose at: WEBER INLET FITTING for 8mm (5/16″) push on hoseClick Here for a Weber 48IDA Suggested Parts List
Browse our Weber Carbs, Manifolds and Parts section
SKU: 30606-M12D