OIL HOSE FITTING, 93-95 RX7 & 04-11 RX8, END WITH CLIP
Oil Hose Fitting, 93-95 & 04-11, End With Clip
| SKU: | 14-850A-N3G1 |
| Manufacturer SKU: | N3G1-14-850A |
OIL HOSE FITTING, 93-95 & 04-11, END WITH CLIP
$55.07
Related Products:
-
OIL COOLER HOSE 93-95 RX7, AT COOLERS DUAL TYPE
Oil Cooler Hose, 93-95, At Coolers, Dual Type
Sorry, this item has been discontinued by Mazda
SKU: 14-830B-N3A3 Manufacturer SKU: N3A3-14-830B -
OIL COOLER HOSE 93-95 RX7, AT REAR HOUSING ALL
Oil Cooler Hose, 93-95, At Rear Housing, All
SKU: 14-720D-N3A1 Manufacturer SKU: N3A1-14-720D -
OIL COOLER HOSE SET, 04-08 RX8 STAINLESS
OIL COOLER HOSE SET, 04-08 RX8 STAINLESS
This set of fully assembled Stainless Steel Braided Hoses replaces the original factory oil cooler hoses on the 2004-2008 RX-8 Manual Transmission models (equipped with dual oil coolers). Costing much less than Mazda replacement units (over $1100 for the complete Mazda set!).
11911 Oil Hose Set-Installation Instructions
Racing Beat’s fully assembled Stainless Steel Braided Hose Set replaces the original factory oil cooler hoses on the 2004-2008 RX-8 Manual Transmission models (equipped with dual oil coolers). Costing much less than Mazda replacement units (over $1100 for the complete Mazda set!), the Racing Beat Oil Hose sets will meet the demands of both street and race.
Simplify your oil line system by replacing the original EIGHT (8) factory lines with the streamlined Racing Beat kit, which contains only the three (3) most critical lines – 1) engine out-to-cooler, 2) cooler-to-cooler, and 3) cooler-to-engine in.
The Mazda factory lines combine both rigid and flexible tubing, and include ten (10) mid-hose connector fittings. Replacing this complex combination of hosing and connectors with a simplified performance-based set eliminates possible areas of leakage during racing and high output applications. As the old saying goes, “Simple is better!” Produced in-house at Racing Beat using Earl’s Auto-Flex stainless steel braid-protected synthetic rubber hose and featuring an inner liner of synthetic rubber, including partial cover of stainless steel braid embedded into the liner during manufacturing. The hose liner is then bonded to a outer protective sheath of stainless steel wire braid. Precision-machined aluminum Earl’s Auto-Seal and Swivel-Seal hose ends ensure a secure and superior seal. Each line is pressure tested by Racing Beat at the end of the assembly process. Unlike earlier rotary applications, replacement of the oil lines on the RX-8 application requires substantial labor effort and is best undertaken when the engine has been removed from the vehicle. Although more challenging due to limited access, this project can be undertaken with engine in the vehicle, just allow adequate time to complete the process. With the engine in the vehicle this is an involved project that can’t be rushed!
Shipped complete with all required oil lines, oil cooler adaptors, engine adaptors, bracket hardware, protective end caps, and fully detailed installation instructions.
SKU: 11911 -
OIL COOLER HOSE 93-95 RX7, AT FRONT COVER SINGLE COOLER
Oil Cooler Hose, 93-95, At Front Cover, Single Cooler
SKU: 14-710D-N3A2 Manufacturer SKU: N3A2-14-710D -
OIL COOLER HOSE SET, 09-11 RX8 STAINLESS
OIL COOLER HOSE SET, 09-11 RX8 STAINLESS
Hoses comes fully assembled, it replaces the 8 original factory oil cooler hoses with just 3 hoses.
1) engine out-to-cooler, 2) cooler-to-cooler, and 3) cooler-to-engine in.
Eliminating possible leakage areas during racing and high output applications.
Each line is pressure tested at the end of the assembly process.
Unlike earlier rotary applications, replacement of the oil lines on the RX-8 application requires substantial labor effort and is best undertaken when the engine has been removed from the vehicle. Although more challenging due to limited access, this project can be undertaken with engine in the vehicle, just allow adequate time to complete the process. With the engine in the vehicle this is an involved project that can’t be rushed! Shipped complete with all required oil lines, oil cooler and engine adaptors, bracket hardware, protective end caps, and fully detailed installation instructions.SKU: 11912 -
OIL COOLER HOSE 93-95, AT COOLER SINGLE TYPE —NLA—
Sorry, this item has been discontinued by Mazda
Oil Cooler Hose, 93-95, At Cooler, Single Type
SKU: 14-830B-N3A1 Manufacturer SKU: N3A1-14-830B
You May Also Like:
-
-
FREEZE PLUG, ROTOR HOUSING @ INTAKE MANIFOLD
Freeze Plug, Rotor Housing @ Intake Manifold
SKU: 555-101 -
-10 HOSE END 90 DEG, -10 HOSE TO 18MM 90
-10 Hose End 90 Degree, -10 Hose To 18mm 90 degree
Designed specifically for 86-92 RX-7’s to fit in between the oil cooler and frame rail, where your conventional 90° bend will not. Also works for 93-95 oil filter tower, which is 18mm if you are making lines.SKU: 7736-9010M18A Manufacturer SKU: 7736-9010M18A -
FREEZE PLUG LARGE, ALL FRONT & REAR HOUSING
1 3/16″ diameter Mazda OEM freeze plug for the larger holes front and rear side housings.
( uses 6-7 depending on year)
SKU: 63-0000-9930 Manufacturer SKU: 9930-63-000 -
HYLOMAR TUBE, 1.5 OZ
HYLOMAR TUBE, 1.5 OZ
Best chemical we have found for water seal O-rings. Brush it on with a trimmed down “acid” brush – in the water seal grooves and then on the seals after you have placed them into the grooves. Stays tacky for a LONG time.
One tube will do one engine easily.
SKU: HYLOMAR
