1971
Clutch and Flywheel
Steel and Aluminum Flywheels Click here for Important Flywheel and Clutch Explanation
-
CLUTCH SLAVE KIT, 71-92 ALL
Clutch Slave Kit, 71-92 All
SKU: 49-4600-FB01 Manufacturer SKU: FB01-49-460 -
CLUTCH THROW OUT BEARING FOR 7.25″ RALLY TWIN DISC RACE CLUTCH
CLUTCH THROW OUT BEARING FOR 7.25″ RALLY TWIN DISC RACE CLUTCH
Use with 7.25″ Rally Double Disc Clutch
SKU: 236521B -
CLUTCH THROW OUT BEARING FOR 7.25″ TWIN DISC RACE CLUTCH
CLUTCH THROW OUT BEARING FOR 7.25″ TWIN DISC RACE CLUTCH
Use with 7.25″ Double Disc clutch
SKU: 236520 -
CLUTCH THROW OUT BEARING, ALL THRU -78 –NLA–
CLUTCH THROW OUT BEARING, ALL THRU -78
Sorry, this item has been discontinued by Mazda.
SKU: 16-5100-0820 Manufacturer SKU: 0820-16-510 -
CLUTCH THROW OUT BEARING, FOR 4.5, 5.5 RACE CLUTCH
Clutch Throw Out Bearing for 4.5″, 5.5″ Race Clutches
SKU: 235520 -
FLYWHEEL RACE FOR 4.5″ CLUTCH Non-Turbo
Race Flywheel For 4.5″ Clutch Non-Turbo
Recommended Torque: 1/4″ bolt = 9-10 ft/lbs
SKU: 02-9207-45NA -
FLYWHEEL RACE FOR 5.5″ CLUTCH NON TURBO DIAMETER
Race Flywheel For 5.5″ Clutch Non Turbo Diameter
Recommended Torque for 5/16″ bolts = 20 lb/ft
SKU: 02-9207-55NA -
FLYWHEEL RACE FOR 7.25″ CLUTCH NON TURBO DIAMETER
Race Flywheel For 7.25″ Clutch Non Turbo Diameter
SKU: 02-9207-725NT -
-
FLYWHEEL STOPPER TOOL, ALL Non-Turbo diameter flywheels
Flywheel Stopper Tool, All Non-Turbo diameter flywheels (Except RX-8’s)
Flywheel stopper makes getting the flywheel / counterweight nut off a LOT easier.
For flywheels 11 3/4″ diameter.SKU: 49-220NT Manufacturer SKU: 49-220NT -
PILOT BEARING REMOVER TOOL
Pilot Bearing Remover Tool
To remove the old pilot bearing the bearing MUST be gripped at its front end. Very few of the aftermarket pullers we tested were able to do this correctly. They often tended to destroy the bearing making removal even harder.
To use the tool simply insert the attachment into the bearing, being sure to get it to the end of the bearing, insert the tapered / threaded end of the slap hammer part and screw them together until the bearing is firmly gripped. Then just “slap hammer” it out. Should take less than a minute.
This tool prevents eccentric shaft damage when removing bearing.
This tool does fit other cars including Miata. We do not have a list of cars that it will work on. The RX pilot bearing/input shaft measures .588″. If your application also has a .588 shaft/bearing, this tool will work.SKU: 49-1285 -
SEAL TRANSMISSION REAR, 71-85 ALL AUTOMATIC + MANUAL TRANS
Rear Transmission Seal, 71-85 All with Automatic and Manual Transmission
SKU: 17-335A-0437 Manufacturer SKU: 0437-17-335A -
TRANSMISSION MOUNT REAR 74-85 COMPETITION–NLA–
Sorry, this item has been discontinued by Mazda
Rear Transmission Mount, 74-85 All Manual Transimission, Competition
SKU: 39-3400-4352 Manufacturer SKU: 4352-39-340