FLYWHEEL STOPPER TOOL
Racing Beat Flywheel Stopper Tool
The Flywheel Stopper Bar Tool is normally required whenever the rotary engine flywheel retaining nut is being removed or installed. The Racing Beat Stopper Bar bolts to either the stock flywheel, the Racing Beat Flywheel, or equivalent (except Tilton) and prevents the flywheel from rotating during the removal process. This is a GREAT timesaving tool, and can be used either in with the engine in the chassis, or while on an engine stand.
| SKU: | 22001 |
FLYWHEEL STOPPER TOOL
Goes nice with the Flywheel Nut Wrench
$38.81
Related Products:
-
FLYWHEEL NUT WRENCH
Racing Beat Flywheel Nut Wrench
Having the correct tool always makes the job seem easy, right? Although you probably won’t be using this tool much, it will certainly pay for itself even if you only use it once! The Flywheel Nut Wrench tool is used to remove or install the 54mm (2.125″) flywheel retaining nut. During re-assembly, this tool will allow you to accurately re-torque the nut to the required 350 foot-pounds This tool can be used with the engine in or out of the chassis.
SKU: 22000 -
FLYWHEEL STOPPER TOOL, TURBO, AUTO TRANS AND RX8
Flywheel Stopper Tool, Turbo, Automatic Transmission And RX8 Manual
SKU: 49-220TB Manufacturer SKU: 49-220TB -
FLYWHEEL STOPPER TOOL, ALL Non-Turbo diameter flywheels
Flywheel Stopper Tool, All Non-Turbo diameter flywheels (Except RX-8’s)
Flywheel stopper makes getting the flywheel / counterweight nut off a LOT easier.
For flywheels 11 3/4″ diameter.SKU: 49-220NT Manufacturer SKU: 49-220NT -
-
SOCKET ADAPTER TOOL, 1/2″ FEMALE TO 3/4″ MALE
Socket Adapter Tool, 1/2″ Female To 3/4″ Male
3/4″ adapter to use 1/2″ drive. The flywheel nut is put on with over 300 foot-pounds of torque and this adapter CAN BREAK! BE CAREFUL!! (sorry – there is no warranty on it). Better to get a hold of a 3/4″ breaker bar that has a warranty from somebody.
(Just to let you know kind of worst case – We have had a few where we needed to use our 1″, 1200 foot pound, impact gun with our 1″ drive impact 54mm socket!)
SKU: 49-22008 -
FLYWHEEL SOCKET TOOL, 54MM IMPACT SOCKET
Flywheel Impact Socket Tool, 54mm, 3/4″ drive
SKU: 49-22009HD
You May Also Like:
-
PORT TEMPLATE TOOL, PORTING BLANK
PORT TEMPLATE TOOL, PORTING BLANK
We no longer make this blank Intake Template.
SKU: 49-222BLANK -
COUNTERWEIGHT PULLER
Counterweight Puller
The Automatic Transmission Counter Balance Weight Puller Tool will remove any automatic transmission balance weight from its taper press fit on the eccentric shaft once the flywheel nut is loosened. This is the same balance weight used with all our lightweight flywheels. (Photo is shown with a Mazda counterweight, which is not included with this tool.)
SKU: 22003 -
CLUTCH DISC ALIGNMENT TOOL, ALL NON-TURBO 72-92
Clutch Disc Alignment Tool, All Non-turbo 72-92
Clutch alignment tools are needed whenever a clutch is installed. Damage to the clutch disc is almost assured if alignment is not correct.
SKU: 0033-05 -
PORT TEMPLATE TOOL, 84-92 6 PORT
Street Port Template Tool
6 Port Intake (contains ports for front, center and rear housings)SKU: 49-2226P -
PORT TEMPLATE TOOL, RACE 13B EXHAUST
Exhaust 13B Race Port Template, 74-95 All Turbo and Non-Turbo
Actual template shown in photo.
The Racing Beat “Race” Exhaust Port Templates for all 13B peripheral port exhaust rotary engines allow you to undertake your own exhaust porting efforts. The race version of these templates open the exhaust port further “upwards”, increasing the port timing duration which results in more intake-exhaust overlap and better high RPM performance.
The Racing Beat laser-cut aluminum porting templates are patterned after their own original master templates. Designed and refined over decades by Racing Beat’s legendary engine builder and co-founder Jim Mederer, this exhaust port template gives you a powerful resource to assist you in your engine upgrade project.
Incredibly easy to use, simply mark the template position as instructed, spray the exhaust port area with marking dye, hold the template in position (we use a simple hand clamp or a office paper clamp), and then scribe the new port shape onto the housing. It’s really that easy.
Porting Effort
During your porting effort we suggest you stay within the boundary of our template shape. This shape has been designed to yield excellent results for a broad range of engine building applications. However, you can certainly get more aggressive with porting efforts beyond the template line, you must then use your own judgment and expertise as a guide.SKU: 22216 -
