SOCKET ADAPTER TOOL, 1/2" FEMALE TO 3/4" MALE

SOCKET ADAPTER TOOL, 1/2″ FEMALE TO 3/4″ MALE

Socket Adapter Tool, 1/2″ Female To 3/4″ Male

3/4″ adapter to use 1/2″ drive. The flywheel nut is put on with over 300 foot-pounds of torque and this adapter CAN BREAK! BE CAREFUL!! (sorry – there is no warranty on it). Better to get a hold of a 3/4″ breaker bar that has a warranty from somebody.

(Just to let you know kind of worst case – We have had a few where we needed to use our 1″, 1200 foot pound, impact gun with our 1″ drive impact 54mm socket!)

SKU: 49-22008

SOCKET ADAPTER TOOL, 1/2″ FEMALE TO 3/4″ MALE

 

$10.84

Related Products:

  • FLYWHEEL SOCKET TOOL, 54MM IMPACT SOCKET

    FLYWHEEL SOCKET TOOL, 54MM IMPACT SOCKET

    Flywheel Impact Socket Tool, 54mm, 3/4″ drive

    SKU: 49-22009HD
    $52.90
    Add to cart
  • FLYWHEEL STOPPER TOOL, TURBO, AUTO TRANS AND RX8

    FLYWHEEL STOPPER TOOL, TURBO, AUTO TRANS AND RX8

    Flywheel Stopper Tool, Turbo, Automatic Transmission And RX8 Manual

    SKU: 49-220TB
    Manufacturer SKU: 49-220TB
    $23.86
    Add to cart
  • COUNTERWEIGHT PULLER

    COUNTERWEIGHT PULLER

    Counterweight Puller

    The Automatic Transmission  Counter Balance Weight Puller Tool will remove any automatic transmission balance weight from its taper press fit on the eccentric shaft once the flywheel nut is loosened. This is the same balance weight used with all our lightweight flywheels. (Photo is shown with a Mazda counterweight, which is not included with this tool.)

    SKU: 22003
    $50.94
    Add to cart
  • FLYWHEEL STOPPER TOOL

    FLYWHEEL STOPPER TOOL

    Racing Beat Flywheel Stopper Tool

    The Flywheel Stopper Bar Tool is normally required whenever the rotary engine flywheel retaining nut is being removed or installed. The Racing Beat Stopper Bar bolts to either the stock flywheel, the Racing Beat Flywheel, or equivalent (except Tilton) and prevents the flywheel from rotating during the removal process. This is a GREAT timesaving tool, and can be used either in with the engine in the chassis, or while on an engine stand.

     

    SKU: 22001
    $38.81
    Add to cart
  • ENGINE STAND, HEAD ONLY-ALL ROTARY

    ENGINE STAND, HEAD ONLY-ALL ROTARY

    Engine Stand, Head Only-All Rotary
    Please note: This is for the HEAD only – actual engine stand is not included (nor is the engine).

    Pipe size is 2 3/8 outside diameter – the most common size. PLEASE be sure your engine stand uses that size!!

    SKU: MZTX-ENG-STAND
    Manufacturer SKU: MZTX-ENG-STAND
    $79.95
    Add to cart
  • FLYWHEEL NUT WRENCH

    FLYWHEEL NUT WRENCH

    Racing Beat Flywheel Nut Wrench

    Having the correct tool always makes the job seem easy, right? Although you probably won’t be using this tool much, it will certainly pay for itself even if you only use it once! The Flywheel Nut Wrench tool is used to remove or install the 54mm (2.125″) flywheel retaining nut. During re-assembly, this tool will allow you to accurately re-torque the nut to the required 350 foot-pounds This tool can be used with the engine in or out of the chassis.

    SKU: 22000
    $58.21
    Add to cart

You May Also Like: