CLUTCH DISC RACE, 83-92 NON TURBO W/TURBO SPLINE

CLUTCH DISC RACE, 83-92 NON TURBO WITH TURBO SPLINE

Racing Beat Race Clutch Disc, 83-92 Non Turbo With Turbo Spline
“Special” Race (for use with 86-92 Turbo Transmission), 4-puck

SKU: 12525

CLUTCH DISC RACE, 83-92 NON TURBO W/TURBO SPLINE

This special application 4-Puck, 225mm Race Clutch Disc is intended for use with the 1987-91 TURBO II gear box, with the larger diameter 23 tooth input shaft, mated to a 225mm flywheel–is designed for drag and road race use. The disc incorporates four (4) sintered copper pucks and a rigid hub for quick, positive engagement, greater fatigue resistance and improved heat dissipation. The sharpened engagement/disengagement characteristics of this disc require careful driver attention – this disc is not intended for street use.

Time Saving Tip: We strongly recommend replacing the throw-out bearing during any clutch work to ensure trouble free performance. Also, we recommend replacing the transmission front and rear seal kit when re-installing the transmission to reduce the possibility of leakage.

Safety Note: None of the Racing Beat, Exedy, Mazda OE, or any aftermarket flywheel or clutch replacement components should ever be allowed to exceed 10,500 RPM under any condition. You must use an engine RPM-limiter to prevent excessive RPM. If your engine is capable of exceeding 8,500 RPM you must install a transmission scatter shield or ballistic blanket. Failure to implement the above may result in serious injury or even death.

$267.75

Related Products:

You May Also Like:

  • CLUTCH DISC RACE, ALL ROTARY -82

    CLUTCH DISC RACE, ALL ROTARY -82

    Racing Beat Race Clutch Disc, All Rotary up to 82, 4 puck

    SKU: 12521
    $267.75
    Add to cart
  • FLYWHEEL STEEL, 74-82 WITHOUT COUNTERWEIGHT

    FLYWHEEL STEEL, 74-82 WITHOUT COUNTERWEIGHT

    Flywheel Steel, 74-82 Without Counterweight

    Does NOT include Counterweight!!

    Applications
    Designed to retain enough mass for comfortable standing starts this flywheel is ideal for street use, yet it is sufficiently lighter to afford a noticeable improvement in low speed acceleration and to make shifting much smoother. For street use our lightweight steel flywheel not only allows the engine to accelerate more rapidly, but it also eliminates much of the rubbery feel that occurs at clutch engagement while shifting.  

    Precision Machining
    Precision CNC-machined from high strength steel, our flywheel assembly is mated to the Mazda OEM ring gear, then surfaced hardened using a ferritic carburizing heat-treating process, creating an extremely durable disc wear surface. The ring gear is thermally-mated to the flywheel and bolted in place for added security to prevent slippage during engagement of the starter motor.

    Weight Comparison
    The weight of the stock flywheel is 23 lbs., compared to 13 lbs for this Flywheel. The actual reduction in inertia from stock is much greater than the weights suggest, since the stock flywheel is 1 to 2 inches thick at its outside edge.

    Retaining Critical Engine Balance
    The installation of an aftermarket flywheel requires the use of a Mazda rear counterweight unit to ensure critical balance of the internal rotating assembly (engine rotors). As produced by Mazda, the original stock rotary flywheel features a pronounced balancing mass included in the flywheel casting. This balancing mass, combined with the stock front counterweight unit, provides the correct balance required for the optimal rotational operation of the engine rotors.

    To allow an aftermarket flywheel to be used on several different rotary engine applications, this balancing mass is eliminated from the design of the rotary flywheel. However, this critical balancing mass must be replaced with an alternative balance weight or risk severe engine damage due to an “unbalanced” engine. A convenient alternative is to install an appropriate rear counterweight from an automatic transmission-equipped RX-7. We offers this counterweight separately if needed.

    Rear Counterweight (Required)
    All aftermarket flywheels require the use of an automatic transmission rear counterweight for correct operation.

    Installation Hardware

    Our Flywheel kits include the flywheel unit and the appropriate mounting hardware, which includes the appropriate tensile-strength hardware to attach the pressure plate to the flywheel.  DO NOT use other aftermarket flywheel mounting kits with the our flywheels. 

    We strongly recommend replacing the throwout bearing during any clutch work to ensure trouble free performance. Also, we recommend replacing the transmission front and rear seal kit when re-installing the transmission to reduce the possibility of leakage.

    Safety Warning
    None of the flywheel or clutch components shown in this site should ever be allowed to exceed 10,500 RPM under any condition. This same RPM limit applies to stock components. You must use an engine RPM-limiter to prevent excessive RPM. If your engine is capable of exceeding 8,500 RPM you must install a transmission scatter shield, or ballistic blanket. Failure to implement the above may result in serious injury or even death.

    SKU: 11436
    $450.00
    Add to cart
  • FLYWHEEL STOPPER TOOL, TURBO, AUTO TRANS AND RX8

    FLYWHEEL STOPPER TOOL, TURBO, AUTO TRANS AND RX8

    Flywheel Stopper Tool, Turbo, Automatic Transmission And RX8 Manual

    SKU: 49-220TB
    Manufacturer SKU: 49-220TB
    $23.86
    Add to cart
  • CLUTCH MASTER, 79-80

    CLUTCH MASTER, 79-80

    Clutch Master, 79-80
    Hose comes out straight up

    SKU: 41-4000-8593
    Manufacturer SKU: 8593-41-400
    $40.16
    Add to cart