EXHAUST MANIFOLD GASKET, 13B REPU (USES 2)
Exhaust Manifold Gasket, All 12A & 13B 74-75 REPU (Uses 2)
Sold individually.
| SKU: | 13-889B-1757 |
| Manufacturer SKU: | 1757-13-889B |
EXHAUST MANIFOLD GASKET, 13B REPU (USES 2)
$8.37
Related Products:
-
FLANGE HEADER TO PIPE, DUAL HOLE STAINLESS
Header to Pipe Flange, Dual Hole Stainless
This cast stainless steel flange can be used to fabricate a custom exhaust for use with the Racing Beat Road Race Header. This two-hole flange measures 6″ X 2-13/16″ and features two openings for use with 2″ OD tubing.
SKU: 16198 -
EXHAUST HEADER GASKET, OUTLET DUAL PIPE
EXHAUST HEADER GASKET, OUTLET DUAL PIPE
Gasket for 16197 Flange, Dual Outlet Pipe
SKU: 16300 -
-
ENGINE TO PIPE FLANGE 12A
12A Engine To Pipe Flange 74-85
This 1/2″ thick laser-cut engine-to-header exhuast flange can be used to fabricate a custom exhaust system for any 1974-85 12A rotary engine. This is the same flange that is used on Racing Beat’s 12A engine- headers.
SKU: 16182 -
EXHAUST PRE-SILENCER, 81-83
Racing Beat Exhaust Pre-Silencer, 71-78, 81-83
The Racing Beat Power Pulse Presilencer for the 1971-78 & 81-83 RX-7 is designed to be used with our wide selection of RX-7 Streetable Headers to complete a bolt-on configuration. These Power Pulse Presilencers are ideal for those individuals wanting to fabricate custom exhaust systems incorporating either long or short primary exhaust systems.
The Power Pulse Presilencer improves the character of the exhaust noise, dramatically reducing the inherent, obnoxious metallic high frequency noise with virtually no power loss. Constructed with a high temperature, 2-inch I.D. perforated core of 304 stainless steel wrapped with high-temperature stainless steel wool, the Power Pulse Presilencer measures 20 inches in length with a 4-inch outside diameter. The mounting studs are 12mm both front and rear.
SKU: 16400
You May Also Like:
-
-
SPLIT AIR EXHAUST GASKET, —NLA— 79-80 HEAT EXCHANGER FRONT & REAR
Split Air Exhaust Gasket, 79-80 Split Air Pipe To Catalytic Converter
Heat Exchanger Front and RearSorry, this item has been discontinued by Mazda
SKU: 13-135B-8527 Manufacturer SKU: 8527-13-135B -
-
EXHAUST STUD, RENESIS EXHAUST MANIFOLD TO ENGINE
Exhaust Stud Renesis, Exhaust Manifold to Engine (4 Required)
SKU: 13-708A-SL50 Manufacturer SKU: SL50-13-708A -
EXHAUST HEADER 13B, 89-92 6PORT DUAL PIPE
Racing Beat 13B Exhaust Header, 89-92 With 6 Port Actuation and O2 sensor fitting.
SKU: 16129 -
EXHAUST HEADER 12A, 81-83 RX7
Racing Beat 12A Exhaust Header, 81-83 RX7. Actual header not shown in photo – oxygen sensor fitting only included on 1984-85 RX-7 GSL-SE header.
This Racing Beat RX-7 Header is designed for a bolt-on installation, when used with the appropriate Racing Beat Power Pulse Presilencer in all 1981-83 RX-7s. The combination of this RX-7 header and the appropriate presilencer replaces the stock exhaust manifold and all catalytic converters for use on racing applications, along with any intermediate pieces of tubing.
The Racing Beat RX-7 header assembly is constructed with .120-inch wall, mandrel-bend, mild steel tubing for increased durability. The engine-to-header flange is laser-cut from 1/2-inch thick steel plate to ensure positive gas sealing. An outlet gasket is included. An engine-to-header gasket is available separately if needed.
SKU: 16010