EXHAUST PRE-SILENCER WITH DOWN PIPE, 89-92 CONVERTIBLE MANUAL TRANSMISSION
Racing Beat Exhaust Pre-Silencer with Down Pipe, 89-92 Non Turbo Manual Transmission Convertible
Down Pipe with Presilencer – 1989-92 RX-7 Convertible Non-Turbo (equipped with Manual Transmission) – The 1986-92 13B 6-port engines, in stock form with the factory fuel injection, produces similar power gains with either our Header/Presilencer combo or our RX-7 Down Pipe/Presilencer combination. If you have no intentions of installing RB’s Holley intake System (or any other aftermarket carb set-up), we recommend the use of the RX-7 Down Pipe/Presilencer combo since it offers a slightly quieter exhaust note, is easier to install and less costly. If you are intending to upgrade the intake or fuel injection system, the Header/Presilencer combo offers the greatest performance potential.
The 1989-92 RX-7 down Pipe/Presilencer combination incorporates a 2.5-inch O.D. Down Pipe and our perforated stainless steel core and stainless steel wool-packed Presilencer to boost power approximately 13% – an 18 horsepower increase on a 1987 RX 7- and maintain a comfortable exhaust noise level during full power driving.
The replacement pipe connects to the factory exhaust manifold, and the presilencer connects to the factory Y-pipe, replacing all catalytic converters and intermediate tubing. It is not possible to use just the down pipe to replace only the catalytic converters. The use of the presilencer is required to complete the connection to the y-pipe. Although a short length of tubing can be substituted in place of the presilencer, we do not offer (or suggest) this due the unacceptable increase in exhaust noise. The down pipe is equipped with a mounting flange for the oxygen sensor. This kit includes all necessary mounting hardware, air control & check valve cover plate, and gaskets (3 Replacement Pipe-to-Presilencer gaskets).
| SKU: | 16217 |
EXHAUST PRE-SILENCER WITH DOWN PIPE, 89-92 CONVERTIBLE MAN TRANS
$534.83
Related Products:
-
MUFFLER ROAD RACE, 86-92 LEFT (DUAL SYSTEM) RACING BEAT
Racing Beat Road Race Muffler, 86-92 Left (Dual System)
Racing Beat’s Road Race mufflers are intended to bolt-up to the outlets of the Road Race Y-Pipe section (16411) only, and are not compatible with the stock or Racing Beat (16447) y-pipe section. These mufflers can be ordered separately for use in custom applications. With over 25 years of exhaust system production experience, Racing Beat has the ability to match the correct internal muffler canister design to the engine’s exhaust output to provide the optimum combination of sound and performance. This muffler canister is manufactured using 304-stainless steel and features a 2-inch diameter straight-through design for maximum performance gains. Finished with a 3.5-inch polished 304 stainless steel tip, this muffler sounds as good as it looks! All stock hanger positions are retained.
SKU: 16439 -
EXHAUST SYSTEM SINGLE, 86-92 NON TURBO WITH RACING BEAT REAR MUFFLERS
Single Exhaust System, 86-92 Non Turbo with Racing Beat Rear Mufflers
SKU: 16-MZTX-0020RB -
EXHAUST PRE-SILENCER, 89-92 NON TURBO MANUAL TRANSMISSION
Racing Beat Exhaust Pre-Silencer, 89-92 Non Turbo Manual Transmission
SKU: 16408 -
Exhaust Down Pipe 86-92 RX7 Convertibles 2 1/2″
Racing Beat Down Pipe for 86-92 RX7 Convertibles 2 1/2″
This Down Pipe is available for use in a 1988-92 RX-7 Convertible application. This 2.5″ OD Down Pipe bolts directly to the stock exhaust manifold and eliminates all catalytic converters, but the use of our presilencer (or a suitable replacement) is required to connect this assembly to the Y-pipe section. If you need to retain a catalytic converter in your exhaust system, you may find a suitable unit offered in the aftermarket. Although the replacement of your stock catalytic converters with a single aftermarket unit is technically NOT legal, this approach may suit your emissions needs. We suggest you contact your local emissions testing facility for more information. Gaskets sold separately.
SKU: S16209 -
MUFFLER ROAD RACE, 86-92 RIGHT (DUAL SYSTEM) RACING BEAT
Racing Beat Road Race Muffler, 86-92 Right Side (Dual System)
Racing Beat’s Road Race mufflers are intended to bolt-up to the outlets of the Road Race Y-Pipe section (16411) only, and are not compatible with the stock or Racing Beat (16447) y-pipe section. These mufflers can be ordered separately for use in custom applications. With over 25 years of exhaust system production experience, Racing Beat has the ability to match the correct internal muffler canister design to the engines exhaust output to provide the optimum combination of sound and performance. This muffler canister is manufactured using 304-stainless steel and features a 2-inch diameter straight-through design for maximum performance gains. Finished with a 3.5-inch polished 304 stainless steel tip, this muffler sounds as good as it looks! All stock hanger positions are retained.
SKU: 16438 -
EXHAUST PRE-SILENCER, 86-92 DUAL PIPE
Racing Beat Exhaust Pre-Silencer, 86-92 Dual Pipe With Gasket & Hardware
SKU: 16448
You May Also Like:
-
-
-
SPLIT AIR EXHAUST GASKET, —NLA— 79-80 HEAT EXCHANGER FRONT & REAR
Split Air Exhaust Gasket, 79-80 Split Air Pipe To Catalytic Converter
Heat Exchanger Front and RearSorry, this item has been discontinued by Mazda
SKU: 13-135B-8527 Manufacturer SKU: 8527-13-135B -
-
EXHAUST STUD, RENESIS EXHAUST MANIFOLD TO ENGINE
Exhaust Stud Renesis, Exhaust Manifold to Engine (4 Required)
SKU: 13-708A-SL50 Manufacturer SKU: SL50-13-708A -
EXHAUST HEADER 12A, 81-83 RX7
Racing Beat 12A Exhaust Header, 81-83 RX7. Actual header not shown in photo – oxygen sensor fitting only included on 1984-85 RX-7 GSL-SE header.
This Racing Beat RX-7 Header is designed for a bolt-on installation, when used with the appropriate Racing Beat Power Pulse Presilencer in all 1981-83 RX-7s. The combination of this RX-7 header and the appropriate presilencer replaces the stock exhaust manifold and all catalytic converters for use on racing applications, along with any intermediate pieces of tubing.
The Racing Beat RX-7 header assembly is constructed with .120-inch wall, mandrel-bend, mild steel tubing for increased durability. The engine-to-header flange is laser-cut from 1/2-inch thick steel plate to ensure positive gas sealing. An outlet gasket is included. An engine-to-header gasket is available separately if needed.
SKU: 16010