1993
Intake
-
WEBER MANIFOLD for PERIPHERAL PORT 13B 48 or 51IDA RACING BEAT PERIPHERAL PORT HOUSING
Weber Manifold for Peripheral Port 13B 48 or 51IDA
This manifold is designed to fit the Racing Beat Periperal Port 13B Rotor Housings.Works with IDA carbs from 48mm to 52mm bore.
The Racing Beat-designed and manufactured Peripheral Port Intake Manifold mates a Weber 48 IDA or 51 IDA downdraft carburetor, or equivalent throttle body, to the Racing Beat-manufactured 13B peripheral port housings. (This manifold cannot be used on the Mazda Factory Race MFR housings.) The steel tubing manifold is attached to the rotor housings with hoses that are included. A simple support bracket fabricated for your particular application, typically attached from the carburetor-manifold junction to the threaded bosses on top of the rotor housings, will complete the task.
Browse our Weber Carbs, Manifolds and Parts section
SKU: 16490 -
WEBER MANIFOLD IDA for 93-95 13B Engines
Racing Beat Weber IDA Manifold for 93-95 13B Engines
48/51+ IDA 1993-95 13B 4-Port Engine or any 13B engine assembled using ’93-95 “Turbo” side housings. Also for any throttle body with an IDA bolt pattern.Note: This manifold does NOT have any hole or fitting for the brake servo hose.
If you want to use the servo then drill and tap a 1/8 NPT (pipe thread) hole somewhere convenient in the rear manifold runner (PRIOR to installation).
Use a straight or 90 degree 5/16″ (8mm) fitting.Click Here for a Weber 48IDA Suggested Parts List
Browse our Weber Carbs, Manifolds and Parts section
SKU: 16495 -
WEBER NUT 8X1.25 WITH 10MM HEX
Weber Nut 8X1.25 With 10mm Hex
These are needed for the larger bore carbs as there is not enough room to get a 12mm wrench correctly on the base nuts.
These use a 10mm wrench which gives you room to tighten the nut.
Hard to find in “not jet nut” style and in steel. They can come in handy in many other places also.Click Here for a Weber 48IDA Suggested Parts List
Browse our Weber Carbs, Manifolds and Parts section
SKU: 967-NUT -
WEBER PHENOLIC SPACER (EACH), 48 OR 51 IDA
Weber 48 or 51 IDA Phenolic Spacer
(Each)The Weber 48/51 IDA Phenolic Intake Spacers can be installed under a 48/51 IDA carburetor to increase the intake manifold length for special applications. Test have shown that up to three spacers per barrel can be used to move the torque peak down about 300 to 500 RPM per spacer. Each spacer is 10mm thick. Two spacers are required,sold individually. Gaskets are not included, but are available separately.
Browse our Weber Carbs, Manifolds and Parts section
SKU: 16621 -
WEBER RAM STACK, 48 IDA
Weber Ram Stack, 48 IDA
Browse our Weber Carbs, Manifolds and Parts section
SKU: 52840.027 -
WEBER RAM STACKS, 51 IDA
Weber Ram Stack, 51 IDA
Sold as a pair
These spun-aluminum air horns are intended for use on a Racing Beat-modified Weber 51 IDA carburetor — When installing these 51 IDA Air Horns the stock “hold down bolts/clamps” provided with the 48 IDA Air Horns are no longer functional; a small amount of RTV silicone applied externally typically secures these air horns in place.Browse our Weber Carbs, Manifolds and Parts section
SKU: 16608 -
WEBER SHAFT LEVER, 48+51IDA MAZDA CABLE
Weber Shaft Lever, 48+51 IDA Mazda Cable
For “U.S. Style” manifolds – where the cable pulls from BELOW shaft.Click Here for a Weber 48IDA Suggested Parts List
Browse our Weber Carbs, Manifolds and Parts section
SKU: 444.614-04 -
WEBER SHAFT LEVER, IDA FOR REVERSE PULL
Weber Shaft Lever, IDA For Reverse Pull
For “Australian Style” manifolds where cable pulls from ABOVE shaft.Browse our Weber Carbs, Manifolds and Parts section
SKU: 444.600-05 -
WEBER SHAFT LEVER, WITH STOP PIN LEFT
Weber Shaft Lever, With Stop Pin Left.
14ga steel
We have these “stops” made for us so the throttle STOP is on the same side of the carb as the throttle PULL. Adjusted correctly this prevents the throttle shaft from being bent when full throttle is applied.
This is our latest design that “includes” the washer that covers the shaft bearing. This also allows more thread engagement of the nut onto the throttle shaft as you no longer use the original bearing cover washer.All descriptions refer to a front mounted rotary engine in a rear wheel drive car.
There are two types of manifold for downdraft IDAs: fuel inlet on engine side with throttle cable pulling from above the throttle shaft, and fuel inlet on the fender side, with the throttle cable pulling from below the throttle shaft. The manifold determines the carb orientation. It is best to have the cable pull, the idle speed screw, throttle stop, and return spring all on the same end of the carb. If this is not done, you will twist the throttle shaft, which can lead to various poor running conditions.
Click Here for a Weber 48IDA Suggested Parts ListBrowse our Weber Carbs, Manifolds and Parts section
SKU: MAT460-L -
WEBER SHAFT LEVER, WITH STOP PIN RIGHT
Weber Shaft Lever, With Stop Pin Right
This STOP is for when the carb fuel inlet is on the Engine side, cable pulling from ABOVE the shaft.
These are for what we call “Australian Style” manifolds.All descriptions refer to a front mounted rotary engine in a rear wheel drive car.
There are two types for downdraft IDA’s: fuel inlet on engine side with throttle cable pulling from above the throttle shaft, and fuel inlet on the fender side, with the throttle cable pulling from below the throttle shaft. The manifold determines the carb orientation. It is best to have the cable pull, the idle speed screw, throttle stop, and return spring all on the same end of the carb. If this is not done, you will twist the throttle shaft, which can lead to various poor running conditions.
With this throttle STOP the throttle STOP is on the same side of the carb as the throttle PULL. Adjusted correctly this prevents the throttle shaft from being bent when full throttle is applied.
And we all know the harder you push on the gas pedal the faster you will go ??Browse our Weber Carbs, Manifolds and Parts section
SKU: MAT460-R -
WEBER SHAFT LOCK TAB
Weber Shaft Lock Tab Washer Fits IDA or DCOE Sold Each
Part can be referenced at #26
Browse our Weber Carbs, Manifolds and Parts section
SKU: 55520.004 Manufacturer SKU: 55520.004 -
WEBER SHAFT NUT
Weber Shaft Nut Fits IDA or DCOE Sold Each
Part can be referenced at #25
Browse our Weber Carbs, Manifolds and Parts section
SKU: 34710.003 -
WEBER SHAFT WASHER
Weber Shaft Washer Fits IDA or DCOE Sold Each
Reference part at #27
Browse our Weber Carbs, Manifolds and Parts section
SKU: 99024.258 -
WEBER SPRING for EITHER IDLE SPEED OR MIXTURE SCREW
Weber Spring for Either Idle Speed or Mixture Screw
Browse our Weber Carbs, Manifolds and Parts section
SKU: 47600.007 -
WEBER STUD, 8X1.25 35MM
Weber Stud, 8X1.25 35mm
Click Here for a Weber 48IDA Suggested Parts List
Browse our Weber Carbs, Manifolds and Parts section
SKU: AV11981 -
WEBER STUD, 8X1.25 45MM
Weber Stud, 8X1.25 45mm
Most of the Weber Manifolds do not include studs to hold the carb to the manifold. These 45mm ones work great when you are using spacers — measure to be sure these are what you need – depends on the spacer thickness.Browse our Weber Carbs, Manifolds and Parts section
SKU: AV11983 -
WEBER TUBE HOLDER IDA, LONG EXTENSION
IDA Long Emulsion Tube Holder
Browse our Weber Carbs, Manifolds and Parts section
SKU: 52580.006 -
Y-PIPE INTAKE GASKET, J-SPEC FD
Y-Pipe Intake Gasket, J-Spec FD
SKU: 13-2340-N3F1 Manufacturer SKU: N3F1-13-234
