WEBER PHENOLIC SPACER (EACH), 48 OR 51 IDA
Weber 48 or 51 IDA Phenolic Spacer
(Each)
The Weber 48/51 IDA Phenolic Intake Spacers can be installed under a 48/51 IDA carburetor to increase the intake manifold length for special applications. Test have shown that up to three spacers per barrel can be used to move the torque peak down about 300 to 500 RPM per spacer. Each spacer is 10mm thick. Two spacers are required,sold individually. Gaskets are not included, but are available separately.
| SKU: | 16621 |
WEBER PHENOLIC SPACER (EACH), 48 OR 51 IDA
$33.92
Related Products:
-
WEBER GASKET BASE, 48 IDA
Weber IDA Base Gasket, 48 IDA
(2) Needed per carbClick Here for a Weber 48IDA Suggested Parts List
Browse our Weber Carbs, Manifolds and Parts section
SKU: 99005.035 -
WEBER 48 IDA, CARBURETOR ONLY
WEBER 48 IDA, CARBURETOR ONLY
Weber 48IDA Carburetor
Be sure to look at our Weber Parts Category for many miscellaneous needed parts.
Weber Parts
Click Here for a Weber 48IDA Suggested Parts List
SKU: C-WEBER-48IDA -
WEBER AFTERMARKET 51IDA CARBURETOR
Weber Aftermarket 51 IDA Carburetor
Supplied with:
48 chokes, f7 tubes, 120 airs, 135 fuel, 0 bypass, 3.0 float needleMost of the IDA manifolds we list are for 48IDA’s — when used with this 51IDA they will need to be ported to match the larger bore.
Click Here for a Weber IDA Suggested Parts List
Be sure to look at our Weber Parts Category for many miscellaneous needed parts.
Weber PartsSKU: 16603 -
WEBER 51 IDA CARBURETOR ONLY
******Click here for our 51 IDA********
Weber 51 IDA Carburetor Only
Racing Beat Modifications
Each carburetor is based on a standard Weber 48mm IDA and then extensively modified in-house by Racing Beat during the conversion process. Using tuning techniques discovered during Racing Beat’s early racing days, these same techniques and modifications are utilized in the methodical transformation of the carburetor as it enlarged to become the Racing Beat 51 IDA.At the start of each carburetor transformation each unit is completely disassembled and inspected. The carburetor bore is machined to the larger 51mm diameter, fitted with precision-made aluminum venturis, emulsion tubes, main and air jets, needle-and-valve, hand-crafted dual throttle plates and shaft, and enlarged diameter air horns with retaining ring.
As delivered, the Racing Beat Weber 51mm IDA carburetor is tuned specifically for a 13B Peripheral Port engine. The Racing Beat Weber 51 IDA carburetor is also suitable for use on a number of rotary engine applications, including a 13B bridge or J-bridge ported engine, or the 12A peripheral ported engine. If the 51 IDA carb is intended for use on these engines; we offer the appropriate Weber components to properly re-tune the carb for these applications. Follow this link for a listing of tuning recommendations for various rotary engine applications. (PDF)
Air Filtration
When considering air filtration for the Weber carburetor you have several options. Open air horns are not recommended due to possibility of engine damage if any debris are ingested by the carburetor. A simple, effective and attractive option are to install a pair of mess air screens. These offer reasonable protection from larger objects, but lack the serious filtration properties of an air filter. The K&N Air Filter Kit is an excellent and easy-to-install option, but the height of the air horns must be trimmed due to clearance concerns within the filter housing. For a dedicated racing application we suggest the fabrication of an enclosed cold-air box. We supply a simple drawing with the instructions highlighting our suggestion for a design, your final design will vary with your application.Performance Comparisons
The selection of an appropriate intake system requires that many factors be taken into consideration. Various intake systems yield different performance characteristics based upon specific engine, exhaust and driveline selections. Due to the complexities associated with these configurations, it is difficult to determine exact power gains for specific applications. Use this intake reference guide (PDF) for performance comparisons between the Weber and Holley Intake systems that we offer.Browse our Weber Carbs, Manifolds and Parts section
SKU: 16602 -
WEBER RAM STACK, 48 IDA
Weber Ram Stack, 48 IDA
Browse our Weber Carbs, Manifolds and Parts section
SKU: 52840.027 -
BOOK WEBER HAYNES, WEBER MANUAL
Book, HAYNES, Weber Manual
Browse our Weber Carbs, Manifolds and Parts section
SKU: 10240
You May Also Like:
-
VALVE AIR CONTROL, 93-95 MANUAL—NLA—
VALVE AIR CONTROL, 93-95 MANUAL
Sorry, this item has been discontinued by Mazda.
SKU: 13-9900-N3A3 Manufacturer SKU: N3A3-13-990 -
VALVE BPAV, 86-88 TURBO —NLA—
VALVE BPAV, 86-88 TURBO
Sorry, this item has been discontinued by Mazda.
SKU: 20-6600-N332 Manufacturer SKU: N332-20-660 -
SOLENOID TURBO CONTROL, 93-95 ON RACK
Turbo Control Solenoid, 93-95 On Rack
SKU: 18-7410-N390 Manufacturer SKU: N390-18-741 -
VALVE VACUUM 1-WAY, GREEN/WHITE CHECK VALVE
1-Way Vacuum Check Valve, Green/White All RX7
SKU: 13-9950-HE41 Manufacturer SKU: HE41-13-995 -
AIR FILTER HOUSING, RACING BEAT STOCK WITHOUT FILTER
Racing Beat Air Filter Housing, Stock without Filter
Racing Beat’s dyno-proven Power Pulse Air Filter Assembly, for all 1971-85 Stock Carburetor Bodies, is designed specifically for performance. While the assembly uses the same Racing Beat foam air filter element that fits the stock canister, the design of the Power Pulse canister both improves air flow into the carburetor and limits the introduction of dirt particles into the filter element. The spun aluminum canister pieces are powder-coated white for added durability.
There is no provision for emission control valve hose/air pump hose connections on this assembly; however, there is a position available to connect a crankcase breather tube if needed.
SKU: 16531 -
AIR FILTER K&N, 79-85 EXCEPT GSLSE —NLA—
Sorry, this item has been discontinued by K&N
Air Filter K&N , 79-85 Except GSLSE
SKU: E2700