1985
General Hardware
-
-
CLUTCH HARDWARE FOR RACE 7.25″ RALLY TWIN
Race Clutch Hardware for 7.25″ Rally Twin
SKU: 298063RY-HW-725 -
CLUTCH RACE HARDWARE, FOR 5.5″ DOUBLE DISC
Race Clutch Hardware, For 5.5″ Double Disc Race Clutches using our Race Flywheels
SKU: 284063-HW-5.5 -
CLUTCH RACE HARDWARE, FOR 7.25″ TWIN DISC
Race Clutch Hardware, For use with 7.25″ Twin disc Clutches using our Race Flywheels
SKU: 298062-HW-725 -
DOWEL PIN FRONT & REAR STATIONARY GEAR TO HOUSING
Front and Rear Stationary Gear to Housing Dowel Pin
SKU: 10-2030-0839 Manufacturer SKU: 0839-10-203 -
DOWEL PIN SHORT, FRONT COVER & BELLHOUSING
Front Cover and Bellhousing Short Dowel Pin
SKU: 10-3090-1757 Manufacturer SKU: 1757-10-309 -
DRY SUMP ADAPTER #1, ALUMINUM AN -12
Aluminum AN Dry Sump Adapter #1, -12
SKU: 14-R960-ZR03 Manufacturer SKU: ZR03-14-R96 -
DRY SUMP ADAPTER #2, ALUMINUM AN -16
Aluminum Dry Sump Adapter #2, AN -16
SKU: 14-R980-ZR03 Manufacturer SKU: ZR03-14-R98 -
FREEZE PLUG LARGE, ALL FRONT & REAR HOUSING
1 3/16″ diameter Mazda OEM freeze plug for the larger holes front and rear side housings.
( uses 6-7 depending on year)
SKU: 63-0000-9930 Manufacturer SKU: 9930-63-000 -
FREEZE PLUG SMALL, FRONT HOUSING
Freeze Plug Small (3/4″ Diameter), Front Housing
(for front side housing, uses 1)SKU: 62-0000-9930 Manufacturer SKU: 9930-62-000 -
FREEZE PLUG, ROTOR HOUSING @ INTAKE MANIFOLD
Freeze Plug, Rotor Housing @ Intake Manifold
SKU: 555-101 -
FRONT ENGINE MOUNT BOLT, PLATE TO FRONT COVER 72-85 (ea)
Front Engine Mount Bolt. Plate to Front Cover. 72-85 RX7 (ea)
SKU: 10-1015-0250 Manufacturer SKU: 0250-10-1015 -
FUEL DOOR BUMP STOP, 81-85 RX7, 93-95 RX7, & 04-11 RX8
Fuel Door Bump Stop (Two per Vehicle)
Fits 81-85 RX7
93-95 RX7
04-11 RX8SKU: 70-4910-0187 Manufacturer SKU: 0187-70-491 -
HYLOMAR TUBE, 1.5 OZ
HYLOMAR TUBE, 1.5 OZ
Best chemical we have found for water seal O-rings. Brush it on with a trimmed down “acid” brush – in the water seal grooves and then on the seals after you have placed them into the grooves. Stays tacky for a LONG time.
One tube will do one engine easily.
SKU: HYLOMAR -
OIL PRESSURE SENDING UNIT PLUG, 1/8 BSP
Oil Pressure Sending Unit Plug, 1/8 BSP, Plug
This is to plug the oil pressure sending unit hole, in the rear side housing, when it is not being used.
It has a 1/8 British Standard Pipe thread — hard to find.
SKU: 31-000J-9950 Manufacturer SKU: 9950-31-000J -
Plug Oil Injector Hole (rotor housings + intake manifold)
Plug for plugging oil injector holes (rotor housings + intake manifold) when they are not being used. Sold EACH, you typically need 2 or 4 depending what you are doing. Fits all oil injector holes from 84-11. Supplied with sealing washer. Uses 3/16 allen wrench.
SKU: 19-064A-FT01-RT Manufacturer SKU: FT01-19-064A-RT -
RIVET PLASTIC, FAN SHROUD LOWER
Plastic Rivet, Fan Shroud Lower
SKU: 40-6580-9926 Manufacturer SKU: 9926-40-658 -
-
SCREW BRAKE ROTOR, ALL YEARS (EACH)
Brake Rotor Screw, All Years, Phillips Flat Head, Counter Sunk
Sold individuallySKU: 10-8200-9983 Manufacturer SKU: 9983-10-820 -
WEBER IDLE SPEED SCREW
Weber Idle Speed Screw
Spring is not included. It is 47600.007Browse our Weber Carbs, Manifolds and Parts section
SKU: 64625.012