PILOT REMOVER TOOL, END PIECE ONLY

You May Also Like:

• 

  SOCKET ADAPTER TOOL, 1/2″ FEMALE TO 3/4″ MALE

  Socket Adapter Tool, 1/2″ Female To 3/4″ Male

  3/4″ adapter to use 1/2″ drive. The flywheel nut is put on with over 300 foot-pounds of torque and this adapter CAN BREAK! BE CAREFUL!! (sorry – there is no warranty on it). Better to get a hold of a 3/4″ breaker bar that has a warranty from somebody.

  (Just to let you know kind of worst case – We have had a few where we needed to use our 1″, 1200 foot pound, impact gun with our 1″ drive impact 54mm socket!)

  SKU:

  49-22008

  $9.94
  Add to cart
• 

  DOWEL PIN REMOVER, END PIECE ONLY

  Dowel Pin Remover, End Piece Only

  SKU:	49-1290-END

  $38.00
  Add to cart
• 

  PORT TEMPLATE TOOL, 84-92 6 PORT

  Street Port Template Tool
  6 Port Intake (contains ports for front, center and rear housings)

  SKU:

  49-2226P

  $39.90
  Add to cart
• 

  PORT TEMPLATE TOOL, RACE 13B EXHAUST

  Exhaust 13B Race Port Template, 74-95 All Turbo and Non-Turbo

  Actual template shown in photo.

  The Racing Beat “Race” Exhaust Port Templates for all 13B peripheral port exhaust rotary engines allow you to undertake your own exhaust porting efforts.  The race version of these templates open the exhaust port further “upwards”, increasing the port timing duration which results in more intake-exhaust overlap and better high RPM performance.

  The Racing Beat laser-cut aluminum porting templates are patterned after their own original master templates. Designed and refined over decades by Racing Beat’s legendary engine builder and co-founder Jim Mederer, this exhaust port template gives you a powerful resource to assist you in your engine upgrade project.

  Incredibly easy to use, simply mark the template position as instructed, spray the exhaust port area with marking dye, hold the template in position (we use a simple hand clamp or a office paper clamp), and then scribe the new port shape onto the housing. It’s really that easy.

  Porting Effort
  During your porting effort we suggest you stay within the boundary of our template shape. This shape has been designed to yield excellent results for a broad range of engine building applications. However, you can certainly get more aggressive with porting efforts beyond the template line, you must then use your own judgment and expertise as a guide.

   

  SKU:

  22216

  $44.88
  Add to cart
• 

  PORT TEMPLATE TOOL, STREET INTAKE 4-PORT

  Port Template Tool, Intake Street Port (4-port)

  Racing Beat Intake Port Templates allows you to undertake your own “street” intake porting effort on most 12A or 13B rotary engines (except 13B 6-port and Renesis). Rotary tuners long ago discovered that changes to the intake port shape will alter intake timing, allowing increased airflow and velocity improvements. These templates are traced from Racing Beat’s own master templates, which are the result of years of research and development. The actual port shapes are traced onto thin sheets of aluminum which you must first cut out, testing your ability to use a die grinder effectively before attempting to port an expensive engine component. The finished Racing Beat porting template is held in place and the porting shape is then traced onto each housing. You must then use your own judgment to develop the port shape within and beyond the scribed line.

  SKU:

  22202

  $65.49
  Add to cart
• 

  CLUTCH DISC ALIGNMENT TOOL, ALL NON-TURBO 72-92

  Clutch Disc Alignment Tool, All Non-turbo 72-92

  Clutch alignment tools are needed whenever a clutch is installed. Damage to the clutch disc is almost assured if alignment is not correct.

  SKU:

  0033-05

  $3.00
  Add to cart