EXHAUST REACTOR GASKET, REAR 76-80 —NLA—
Exhaust Thermal Reactor Gasket, Rear 76-80 Has been discontinued by Mazda
| SKU: | 13-891A-8871 |
| Manufacturer SKU: | 8871-13-891A |
EXHAUST REACTOR GASKET, REAR 76-80
$0.00
Related Products:
-
EXHAUST MANIFOLD GASKET, 12A THRU 80 FEDERAL
Exhaust Manifold Gasket, 12A Through 80 Federal
SKU: 13-4610-N2Y0 Manufacturer SKU: N2Y0-13-461 -
EXHAUST REACTOR GASKET, BOTTOM 79-80 RX7
Exhaust Reactor Gasket, Bottom
79-80 Bottom of Thermal Reactor
Mazda has discontinued this gasket but we have a bunch left.SKU: 40-4290-8501 Manufacturer SKU: 8501-40-429 -
EXHAUST HEADER GASKET, OUTLET DUAL PIPE
EXHAUST HEADER GASKET, OUTLET DUAL PIPE
Gasket for 16197 Flange, Dual Outlet Pipe
SKU: 16300 -
SPLIT AIR EXHAUST GASKET, —NLA— 79-80 RX7 HEAT EXCHANGER FRONT & REAR
Split Air Exhaust Gasket, 79-80 Split Air Pipe To Catalytic Converter
Heat Exchanger Front and RearSorry, this item has been discontinued by Mazda
SKU: 13-135B-8527 Manufacturer SKU: 8527-13-135B -
EXHAUST HEAT EXCHANGER GASKET, FRONT 76-80 RX7
79-80 Front of Heat Exchanger Gasket
SKU: 40-3050-N2Y1 Manufacturer SKU: N2Y1-40-305 -
EXHAUST HEAT EXCHANGER GASKET REAR 76-80—NLA–
Sorry, this item has been discontinued by Mazda
EXHAUST HEAT EXCHANGER GASKET, REAR 76-80
SKU: 40-3050-N2Y0 Manufacturer SKU: N2Y0-40-305
You May Also Like:
-
EXHAUST STUD, RENESIS EXHAUST MANIFOLD TO ENGINE
Exhaust Stud Renesis, Exhaust Manifold to Engine (4 Required)
SKU: 13-708A-SL50 Manufacturer SKU: SL50-13-708A -
EXHAUST HEADER 13B, 74-78 NO FLANGE EXCEPT PICK UP
Racing Beat 13B Exhaust Header, 74-78 No Flange. Will not work on the Pick Up
This rotary exhaust Header/Collector (less outlet flange) is ideal for RX-2, RX-3, RX-4, and COSMO (does not fit rotary pickup) custom exhaust installations. The flame-cut, .5-inch thick engine flange provides positive sealing and alignment. By integrating the collector with the header we reduce the effort and cost in completing the exhaust system. Engine-to-pipe gaskets are not included but are available separately. An Air Control and Check Valve Cover Plate is required when using this header with a stock intake system.
If the stock resonator is eliminated during installation of this unit, we strongly recommend selecting a Power Pulse Presilencer and installing it in place of the resonator to maintain a pleasant noise level and character.
SKU: 16007 -
EXHAUST CONVERTER GASKET, 93-95 RX7 MAIN FRONT & REAR
Exhaust Converter Gasket 93-95 Front and Rear of Main
SKU: 40-3050-RF36 Manufacturer SKU: RF36-40-305 -
-
EXHAUST PRE-SILENCER WITH DOWN PIPE, 88 CONVERTIBLE MANUAL
Racing Beat Exhaust Pre-Silencer with Down Pipe, 88 Convertible Manual Transmission Non-Turbo
Down Pipe with Presilencer – 1988 RX-7 Convertible Non-Turbo (w/Manual Transmission) – The 1986-92 13B 6-port engines, in stock form with the factory fuel injection, produces similar power gains with either our Header/Presilencer combo or our RX-7 Down Pipe/Presilencer combination. If you have no intentions of installing RB’s Holley intake System (or any other aftermarket carb set-up), we recommend the use of the down pipe/Presilencer combo since it offers a slightly quieter exhaust note, is easier to install and less costly. If you are intending to upgrade the intake or fuel injection system, the Header/Presilencer combo offers the greatest performance potential.
The 1988 RX-7 Convertible (w/ Manual Transmission) Down Pipe/Presilencer combination incorporates a 2.5-inch O.D. Down Pipe and our perforated stainless steel core and stainless steel wool-packed Presilencer to boost power approximately 13% – an 18 horsepower increase on a 1987 RX 7- and maintain a comfortable exhaust noise level during full power driving.
The replacement pipe connects to the factory exhaust manifold, and the presilencer connects to the factory Y-pipe, replacing all catalytic converters and intermediate tubing. (The downpipe cannot be used as a “bolt-up” component to replace just the catalytic converters.)
The Racing Beat presilencer is equipped with an exhaust back-pressure tube for correct operation of the 6-port actuators. Installation of this requires the removal of the air control and check valve and the air pump. This kit includes all necessary mounting hardware, air control & check valve cover plate, and gaskets (1 Back Pressure Pick-up and 3 Replacement Pipe-to-Presilencer gaskets).
SKU: 16209 -
MUFFLER UNIVERSAL, POWER PULSE 79-85 RX7 RACING BEAT
Racing Beat Universal Power Pulse Muffler, 79-85
In response to numerous requests from customers demanding a very low restriction“street capable” muffler, Racing Beat now offers the Universal Power Pulse PR-Extreme RX-7 Muffler with a 2.75″ OD internal perforated core design to meet the performance demands of high-horsepower ported rotary engines. The Power Pulse PR-Extreme RX-7 Muffler is compatible with all 1979-85 RX-7 muffler rear mounting positions and retains the factory stock appearance; this PR-Extreme RX-7 Muffler includes an inlet of 3″.
The Racing Beat Universal Power Pulse PR-Extreme RX-7 Muffler is manufactured by the same exhaust components manufacturer that has produced the “tried and proven” First Generation RX-7 Power Pulse mufflers (1979-80, 1981-82, and 1984-85) since the mid-1980s. Utilizing a heavy-walled canister shell and extremely durable heat and noise insulating materials, the Racing Beat Power Pulse PR-Extreme RX-7 Muffler is engineered for the high exhaust gas temperatures found in rotary engine applications.
The main body of the muffler canister measures 8 inches in diameter and 18 inches in length. The dual outlet tips are completely chrome-plated with straight-cut outlet.
Now may be the time to consider replacing the old rubber muffler hangers on your RX-7. New replacement hangers will ensure correct alignment of the RX-7 muffler canister and tip position in the bumper opening.
SKU: 16436