WEBER STUD, 8X1.25 45MM
Weber Stud, 8X1.25 45mm
Most of the Weber Manifolds do not include studs to hold the carb to the manifold. These 45mm ones work great when you are using spacers — measure to be sure these are what you need – depends on the spacer thickness.
| SKU: | AV11983 |
WEBER STUD, 8X1.25 45MM
$1.64
Related Products:
-
WEBER IDA BASE GASKET, 3MM THICK
Weber IDA Base Gasket, 3mm Thick
Browse our Weber Carbs, Manifolds and Parts section
SKU: 99005.123 -
BOOK WEBER HAYNES, WEBER MANUAL
Book, HAYNES, Weber Manual
Browse our Weber Carbs, Manifolds and Parts section
SKU: 10240 -
WEBER NUT 8X1.25 WITH 10MM HEX
Weber Nut 8X1.25 With 10mm Hex
These are needed for the larger bore carbs as there is not enough room to get a 12mm wrench correctly on the base nuts.
These use a 10mm wrench which gives you room to tighten the nut.
Hard to find in “not jet nut” style and in steel. They can come in handy in many other places also.Click Here for a Weber 48IDA Suggested Parts List
Browse our Weber Carbs, Manifolds and Parts section
SKU: 967-NUT -
WEBER INLET FITTING, AN -6 TO WEBER 12MM
-6 To Weber 12mm Inlet Fitting
All Weber IDA carbs come with a useless banjo fitting we have never figured out how to use (unless you tap it 1/8-pipe and use a “barb” fitting). This will replace the stock inlet fitting with -6AN so you can use braided hose.
The 12mm Stat-O-Seal is strongly recommended for this fitting — it is at: WEBER INLET SEAL, STAT-O-SEAL FOR 12MM
We also have a 90° fitting for 8mm / 5/16″ push on hose at: WEBER INLET FITTING for 8mm (5/16″) push on hoseClick Here for a Weber 48IDA Suggested Parts List
Browse our Weber Carbs, Manifolds and Parts section
SKU: 30606-M12D -
WEBER PHENOLIC SPACER (EACH), 48 OR 51 IDA
Weber 48 or 51 IDA Phenolic Spacer
(Each)The Weber 48/51 IDA Phenolic Intake Spacers can be installed under a 48/51 IDA carburetor to increase the intake manifold length for special applications. Test have shown that up to three spacers per barrel can be used to move the torque peak down about 300 to 500 RPM per spacer. Each spacer is 10mm thick. Two spacers are required,sold individually. Gaskets are not included, but are available separately.
Browse our Weber Carbs, Manifolds and Parts section
SKU: 16621 -
WEBER FLOAT NEEDLE IDA, 3.0 MM
Weber Float Needle IDA, 3.0 mm
Rotary engines using IDA carbs need the largest float needle you can find. This 3.0 is the largest currently avialable.Weber IDA Float Needle Crush Washer
Click Here for a Weber 48IDA Suggested Parts List
Browse our Weber Carbs, Manifolds and Parts section
SKU: 79504.300
You May Also Like:
-
BPAV GASKET, 84-85 GSLSE
Bypass Air Control Valve Gasket 84-85
SKU: 13-7210-N386 Manufacturer SKU: N386-13-721 -
AIR FILTER HOUSING, RACING BEAT STOCK WITHOUT FILTER
Racing Beat Air Filter Housing, Stock without Filter
Racing Beat’s dyno-proven Power Pulse Air Filter Assembly, for all 1971-85 Stock Carburetor Bodies, is designed specifically for performance. While the assembly uses the same Racing Beat foam air filter element that fits the stock canister, the design of the Power Pulse canister both improves air flow into the carburetor and limits the introduction of dirt particles into the filter element. The spun aluminum canister pieces are powder-coated white for added durability.
There is no provision for emission control valve hose/air pump hose connections on this assembly; however, there is a position available to connect a crankcase breather tube if needed.
SKU: 16531 -
VALVE AIR CONTROL, CHECK VALVE- ALL
Check Valve for All Air Control Valves
SKU: 13-7300-1480 Manufacturer SKU: 1480-13-730 -
BPAV GASKET, 86-88 ALL
Bypass Air Control Valve Gasket 86-88 All
SKU: 20-661A-N326 Manufacturer SKU: N326-20-661A -
VALVE BPAV, 86-88 NON-TURBO
By Pass Air Valve, 86-88 Non-Turbo
SKU: 20-6600-N326 Manufacturer SKU: N326-20-660 -
SOLENOID TURBO CONTROL, 93-95 ON RACK
Turbo Control Solenoid, 93-95 On Rack
SKU: 18-7410-N390 Manufacturer SKU: N390-18-741