1992
Hardcore Racing
-
FLYWHEEL Mazdaspeed RACE 5.5″, FOR 5.5″ RACE CLUTCH NA–NLA–
Race Flywheel for 5.5″ Race Clutch. Fits all non-turbo diameter bell housings. (11.75 diameter and 116 tooth)
3.9 LBS
Accepts 5.5″ clutch ONLY
Our Hardware Kit #284063-HW-5.5 will NOT work on this flywheel. Customer must supply their own hardware for this flywheel.
When using this flywheel, you MUST modify your rear counterweight with additional holes and reduce hub diameter.Sorry, this item has been discontinued by Mazda
Click here for a templateSKU: 02-9207-0000 Manufacturer SKU: 0000-02-9207 -
FLYWHEEL RACE FOR 4.5″ CLUTCH “TURBO” DIAMETER + RX8
Race Flywheel for 4.5″ Clutch “Turbo” Diameter
Works on RX8Recommended Torque: 1/4″ bolt = 9-10 ft/lbs
SKU: 02-9207-45TB -
FLYWHEEL RACE FOR 4.5″ CLUTCH Non-Turbo
Race Flywheel For 4.5″ Clutch Non-Turbo
Recommended Torque: 1/4″ bolt = 9-10 ft/lbs
SKU: 02-9207-45NA -
FLYWHEEL RACE FOR 5.5″ CLUTCH NON TURBO DIAMETER
Race Flywheel For 5.5″ Clutch Non Turbo Diameter
Recommended Torque for 5/16″ bolts = 20 lb/ft
SKU: 02-9207-55NA -
FLYWHEEL RACE FOR 5.5″ CLUTCH TURBO + RX8
Race Flywheel For 5.5″ Clutch Turbo
Works with RX8Recommended Torque for 5/16″ bolts = 20 lb/ft
SKU: 02-9207-55TB -
FLYWHEEL RACE FOR 7.25″ CLUTCH NON TURBO DIAMETER
Race Flywheel For 7.25″ Clutch Non Turbo Diameter
SKU: 02-9207-725NT -
FLYWHEEL RACE FOR 7.25″ CLUTCH TURBO DIAMETER + RX8
Race Flywheel for 7.25″ Clutch Turbo Diameter
Works on RX8SKU: 02-9207-725TB -
-
FLYWHEEL RACE REPLACEMENT FRICTION PLATE 7.25″ N/A
Race Flywheel Replacement Friction Plate 7.25″ Non Turbo
This is a replacement friction plate for our 7.25″ race flywheel for the non-turbo diameter (11 3/4″).
New bolts and nuts for installation are included.
Note: The bellhousing and starter determine the diameter of flywheel needed, With all the race car transmission combinations out there Turbo versus non-turbo can sometimes be not the best definition – better to measure your flywheel diameter.
SKU: HS7450 -
FLYWHEEL RACE REPLACEMENT FRICTION PLATE 7.25″ TURBO
Race Flywheel Replacement Friction Plate 7.25″ Turbo
Works on RX8This is a replacement friction plate for our 7.25″ race flywheel for the Turbo diameter (12 1/2″).
New bolts and nuts for installation are included.
Note: The bellhousing and starter determine the diameter of flywheel needed, With all the race car transmission combinations out there Turbo versus non-turbo can sometimes be not the best definition – better to measure your flywheel diameter.
SKU: HS50603 -
FLYWHEEL REPLACEMENT FRICTION SURFACE FOR MAZDATRIX 240mm ALUMINUM FLYWHEEL
Flywheel Replacement Friction Plate for MAZDATRIX 225mm (9″) Non Turbo flywheel.
This is a replacement friction plate for our 240mm ALUMINUM flywheel for the Turbo / RX8 12-1/2″ diameter flywheel.
New bolts and nuts for installation are included.
Note: The bellhousing and starter determine the diameter of flywheel needed, With all the race / street car transmission combinations out there Turbo versus non-turbo can sometimes be not the best definition – better to measure your flywheel diameter.
SKU: HS9587T Manufacturer SKU: HS9587T -
RACE BUMPSTEER KIT, LONG COUPLING NUT
Race Bumpsteer Kit, Long Coupling Nut
For our Bumpsteer Kit. Couples the steering rack end to the heim joint on our Bumpsteer Kit Stud.
Threaded M14x2.0 for the hiem joint, M12x1.25 for the tie rod and is 3″ longSKU: R-BSK-COUP-L -
RACE STEERING ANGLE, COUPLING NUT (F-F)
Race Steering Angle Coupling Nut (F-F)
For our Steering Angle Kit. Connects the rack steering arm to the heim joint on the stud.
Threaded M14x2.0 for the hiem joint, M12x1.25 for the tie rod and is 1-3/8″ longSKU: R-SAK-COUP-S -
-
RACE STEERING ANGLE, HEIM JOINT 14X2.0 MM
Race Steering Angle Heim Joint 14×2.0 mm
14mm Heim for our Steering Angle kit and our Bumpsteer kit. Goes over the stud and threads into the coupler. About 1/2″ of the threads need to be cut off before installation.
SKU: R-SAK-HEIM -
RACE STEERING ANGLE, RACK COUPLER (MALE-FEMALE)
Race Steering Angle Rack Coupler (Male-Female)
For our Steering Angle Kit. Screws into the steering rack to allow more steering angle. Two needed per car. Will NOT work without doing other things to allow correct alignment.
SKU: R-SAK-RACKEND -
-
SERVICE CUT 3MM APEX SEAL GROOVE RX7 or RX8
SERVICE CUT 3MM APEX SEAL GROOVE in 2MM RX7 or RX8 Rotors
Price is to do a PAIR of rotors. Price DOES NOT INCLUDE the rotors.
Either buy them new from us or ship your pair to us.
Turn around is approximately 3 weeks from when rotors are received AT Mazdatrix. Time does NOT include shipping back to you.
SKU: SV-CUT-3MM-RX7
