1977
General Hardware
-
-10 CAP PLASTIC, FITS -10 MALE END
-10 Plastic Cap, Fits -10 Male End
Plastic Cap for male end
These come in very handy when you are removing the engine or cooler, to prevent debris from getting in.
SKU: -10-CAP -
-10 HOSE END 45 DEGREE, TUBE
-10 Hose End 45 Degree, Tube 45 Degree
There are some custom applications where the available oil cooler line sets will just not work, and special length lines need to be assembled. We carry -10 ends in either straight, 45 degree, or 90 degree, as well as -10 hose.SKU: -10-END-45 -
-10 HOSE END 90 DEGREE, TUBE 90 DEGREE
-10 Hose End 90 Degree, Tube 90 Degree
There are some custom applications where the available oil cooler line sets will just not work, and special length lines need to be assembled. We carry -10 ends in either straight, 45 degree, or 90 degree, as well as -10 hose.SKU: -10-END-90 -
-10 HOSE END, STRAIGHT
-10 Hose End, Straight
There are some custom applications where the available oil cooler line sets will just not work, and special length lines need to be assembled. We carry -10 ends in either straight, 45 degree, or 90 degree, as well as -10 hose.SKU: -10-END -
-10 PLUG PLASTIC, FITS -10 FEMALE END
-10 Plastic Plug, Fits -10 Female End
These come in very handy when you are removing the engine or cooler, to prevent debris from getting in, and oil from leaking out.
SKU: -10-PLUG -
10MM CRUSH WASHER 74-11 WATER DRAIN ETC
Water Drain Plug Crush Washer 10mm 74-11
SKU: 41-0000-9956 Manufacturer SKU: 9956-41-000 -
ADAPTER -10 16MM THREAD, -85 COOLER AND -91 FRONT COVER
Adapter, -10, 16mm Thread, Up to 85 Cooler And Up to 91 Front Cover.
SKU: 11901 -
ADAPTER -10 18MM THREAD, 86+ COOLER & ALL REAR HOUSING
Adapter -10, 18mm Thread, 86+ Cooler & All Rear Housing
SKU: 11902 -
ADAPTER WATER TEMPERATURE, 3/8 NPT TO MECHANICAL TEMPERATURE GAUGE
Water Temperature, 3/8 NPT To Mechanical Temperature Gauge Adapter
SKU: 2263 -
BATTERY HOLD DOWN, NUT 6MM BIG FLANGE
Battery Hold Down Nut, 6mm Big Flange
SKU: 00-603B-9994 Manufacturer SKU: 9994-00-603B -
BOLT STARTER LOWER, 72-85 COARSE THREAD —NLA—
BOLT STARTER LOWER, 72-85 COARSE THREAD
Sorry, this item has been discontinued by Mazda
SKU: 11-0320-9980 Manufacturer SKU: 9980-11-032 -
BOLT STARTER LOWER, 72-92 COARSE THREAD
Lower Starter Bolt, 72-92 Coarse Thread
SKU: 18-4010-N327 Manufacturer SKU: N327-18-401 -
BOLT STARTER UPPER, ALL -85
Upper Starter Bolt, All up to 85
Note: which upper starter bolt you use is determined by the starter, not the engine
SKU: 31-0125-9980 Manufacturer SKU: 9980-31-0125 -
BOTTOM STARTER STUD, 74-92 ALL
Bottom Starter Stud, 74-92 All
Tired of trying to find that ONE COARSE thread bolt for the bottom of the starter?
Replace it with this coarse/fine stud and use the same nut / thread as all the other bellhousing bolts!SKU: STUD10x1.5-1.25 -
CLUTCH HARDWARE FOR RACE 7.25″ RALLY TWIN
Race Clutch Hardware for 7.25″ Rally Twin
SKU: 298063RY-HW-725 -
CLUTCH RACE HARDWARE, FOR 5.5″ DOUBLE DISC
Race Clutch Hardware, For 5.5″ Double Disc Race Clutches using our Race Flywheels
SKU: 284063-HW-5.5 -
CLUTCH RACE HARDWARE, FOR 7.25″ TWIN DISC
Race Clutch Hardware, For use with 7.25″ Twin disc Clutches using our Race Flywheels
SKU: 298062-HW-725 -
DOWEL PIN FRONT & REAR STATIONARY GEAR TO HOUSING
Front and Rear Stationary Gear to Housing Dowel Pin
SKU: 10-2030-0839 Manufacturer SKU: 0839-10-203