FLYWHEEL DOWEL PIN, ALL
Flywheel Dowel Pin, All
Flywheel Dowel Pins have been needed a few times when someone has damaged them, or the machine shop surfacing the flywheel “lost” them.
| SKU: | 30-8220-9923 |
| Manufacturer SKU: | 9923-30-822 |
FLYWHEEL DOWEL PIN, ALL
$5.04
Related Products:
-
FLYWHEEL SOCKET TOOL, 54MM IMPACT SOCKET
Flywheel Impact Socket Tool, 54mm, 3/4″ drive
SKU: 49-22009HD -
FLYWHEEL STOPPER TOOL ALL N/A diameter flywheels
Flywheel Stopper Tool, All Non-Turbo diameter flywheels (Except RX-8’s)
Flywheel stopper makes getting the flywheel / counterweight nut off a LOT easier.
For flywheels 11 3/4″ diameter.SKU: 49-220NT Manufacturer SKU: 49-220NT -
NUT FLYWHEEL, FLYWHEEL/ECCENTRIC
Flywheel Nut, Flywheel/Eccentric Shaft
SKU: 11-711C-0810 Manufacturer SKU: 0810-11-711C -
DOWEL PIN REMOVER TOOL
Dowel Pin Remover Tool
Tool makes pulling the dowels out of the rotor and side housings a piece of cake during engine dis-assembly.
SKU: 49-1290 -
FLYWHEEL STOPPER TOOL, TURBO, AUTO TRANS AND RX8
Flywheel Stopper Tool, Turbo, Automatic Transmission And RX8 Manual
SKU: 49-220TB Manufacturer SKU: 49-220TB -
You May Also Like:
-
CLUTCH SLAVE HOSE, 04-11 RX8 HARD @ MASTER
Clutch Slave Hardline Hose, 04-11 RX8 @ Master
SKU: 45-510A-FE05 Manufacturer SKU: FE05-45-510A -
FLYWHEEL RING GEAR, RX7 NON TURBO
Flywheel Ring Gear, RX7 Non Turbo
SKU: 11-7020-0866 Manufacturer SKU: 0866-11-702 -
CLUTCH FORK BOOT 86-92 RX7 TURBO
Clutch Fork Boot 86-92 Turbo
SKU: 16-2140-N302 Manufacturer SKU: N302-16-214 -
TRANS FRONT COVER 81-85 12A THIN BEARING–NLA–
Transmission Front Cover, 81-85 12A (Thin Bearing)
5-spd (use with 81+ front bearing)Sorry, this item has been discontinued by Mazda
SKU: 16-220D-8540 Manufacturer SKU: 8540-16-220D -
CLUTCH DISC, ALL ROTARY -82
Clutch Disc, All Rotary up to 82
Stock/Original EquipmentSKU: 16-460A-HE11 Manufacturer SKU: HE11-16-460A -
CLUTCH DISC RACE, ALL ROTARY -82
Racing Beat Race Clutch Disc, All Rotary up to 82, 4 puck
The 4-Puck 215mm Race Clutch Disc is designed for drag and road race use with all 1971-82 12A & 13B Applications (except Rotary Pick-Up). The disc incorporates four (4) sintered copper pucks and a rigid hub for quick, positive engagement, greater fatigue resistance, and improved heat dissipation. The sharpened engagement/disengagement characteristics of this disc require careful driver attention – this disc is not intended for street use.
Time Saving Tip: We strongly recommend replacing the throw-out bearing during any clutch work to ensure trouble free performance. Also, we recommend replacing the transmission front and rear seal kit when re-installing the transmission to reduce the possibility of leakage.
Safety Note: None of the Racing Beat, Exedy, Mazda OE, or any aftermarket flywheel or clutch replacement components should ever be allowed to exceed 10,500 RPM under any condition. You must use an engine RPM-limiter to prevent excessive RPM. If your engine is capable of exceeding 8,500 RPM you must install a transmission scatter shield or ballistic blanket. Failure to implement the above may result in serious injury or even death.
Actual disc not shown in photo.
SKU: 12521