ENDURANCE FLYWHEEL RACE FOR 4.5" CLUTCH "TURBO" DIAMETER + RX8
ENDURANCE FLYWHEEL RACE FOR 4.5" CLUTCH "TURBO" DIAMETER + RX8
ENDURANCE FLYWHEEL RACE FOR 4.5" CLUTCH "TURBO" DIAMETER + RX8
ENDURANCE FLYWHEEL RACE FOR 4.5" CLUTCH "TURBO" DIAMETER + RX8
ENDURANCE FLYWHEEL RACE FOR 4.5" CLUTCH "TURBO" DIAMETER + RX8

ENDURANCE FLYWHEEL RACE FOR 4.5″ CLUTCH “TURBO” DIAMETER + RX8

Endurance Race Flywheel for 4.5″ Clutch “Turbo” Diameter
Works on RX8

Recommended Torque: 1/4″ bolt = 9-10 ft/lbs

Our racing flywheels are the lightest ones we know of – they are specially made for us.

They are made from billet MIL-spec 6061 aluminum and hard anodized to MIL specs.

This one is for 4.5″ diameter racing clutches. The clutches we sell are double disc. Flywheel is 12 1/2″ diameter, 125 tooth, and weighs 5.5 pounds with the friction plate. Does not include the rear counterweight. Hardware to mount flywheel to counterweight (#95179) and clutch to flywheel are not included and available separately.

These are NOT suitable for street driving — serious racing only, specifically road racing.

Bellhousing and starter are what actually determine the diameter of flywheel needed – it is best to measure yours.

SKU: 02-9207-45TBE

ENDURANCE FLYWHEEL RACE FOR 4.5″ CLUTCH “TURBO” DIAMETER + RX8

 

$688.00

Related Products:

You May Also Like:

  • CLUTCH MASTER, 79-80

    CLUTCH MASTER, 79-80 RX7

    Clutch Master, 79-80
    Hose comes out straight up

    SKU: 41-4000-8593
    Manufacturer SKU: 8593-41-400
    $58.87
    Add to cart
  • FLYWHEEL ALUMINUM, 74-82 W/O COUNTERWEIGHT

    FLYWHEEL ALUMINUM, 74-82 (Does NOT include counterweight)

    FLYWHEEL ALUMINUM, 74-82 W/O COUNTERWEIGHT

    For 74-82 style CLUTCHES — The actual flywheel ONLY fits 74-92 non-turbos. The CLUTCH HARDWARE  (included) is what differs.
    The 74-82 clutch pressure plate uses no spacers while the 83-92 (non-turbo) pressure plates need the spacers. 

    SKU: 11433
    $577.50
    Add to cart
  • FLYWHEEL STEEL, 74-82 WITHOUT COUNTERWEIGHT

    FLYWHEEL STEEL, 74-82 WITHOUT COUNTERWEIGHT

    Flywheel Steel, 74-82 Without Counterweight

    Does NOT include Counterweight!!

    Applications
    Designed to retain enough mass for comfortable standing starts this flywheel is ideal for street use, yet it is sufficiently lighter to afford a noticeable improvement in low speed acceleration and to make shifting much smoother. For street use our lightweight steel flywheel not only allows the engine to accelerate more rapidly, but it also eliminates much of the rubbery feel that occurs at clutch engagement while shifting.  

    Precision Machining
    Precision CNC-machined from high strength steel, our flywheel assembly is mated to the Mazda OEM ring gear, then surfaced hardened using a ferritic carburizing heat-treating process, creating an extremely durable disc wear surface. The ring gear is thermally-mated to the flywheel and bolted in place for added security to prevent slippage during engagement of the starter motor.

    Weight Comparison
    The weight of the stock flywheel is 23 lbs., compared to 13 lbs for this Flywheel. The actual reduction in inertia from stock is much greater than the weights suggest, since the stock flywheel is 1 to 2 inches thick at its outside edge.

    Retaining Critical Engine Balance
    The installation of an aftermarket flywheel requires the use of a Mazda rear counterweight unit to ensure critical balance of the internal rotating assembly (engine rotors). As produced by Mazda, the original stock rotary flywheel features a pronounced balancing mass included in the flywheel casting. This balancing mass, combined with the stock front counterweight unit, provides the correct balance required for the optimal rotational operation of the engine rotors.

    To allow an aftermarket flywheel to be used on several different rotary engine applications, this balancing mass is eliminated from the design of the rotary flywheel. However, this critical balancing mass must be replaced with an alternative balance weight or risk severe engine damage due to an “unbalanced” engine. A convenient alternative is to install an appropriate rear counterweight from an automatic transmission-equipped RX-7. We offers this counterweight separately if needed.

    Rear Counterweight (Required)
    All aftermarket flywheels require the use of an automatic transmission rear counterweight for correct operation.

    Installation Hardware

    Our Flywheel kits include the flywheel unit and the appropriate mounting hardware, which includes the appropriate tensile-strength hardware to attach the pressure plate to the flywheel.  DO NOT use other aftermarket flywheel mounting kits with the our flywheels. 

    We strongly recommend replacing the throwout bearing during any clutch work to ensure trouble free performance. Also, we recommend replacing the transmission front and rear seal kit when re-installing the transmission to reduce the possibility of leakage.

    Safety Warning
    None of the flywheel or clutch components shown in this site should ever be allowed to exceed 10,500 RPM under any condition. This same RPM limit applies to stock components. You must use an engine RPM-limiter to prevent excessive RPM. If your engine is capable of exceeding 8,500 RPM you must install a transmission scatter shield, or ballistic blanket. Failure to implement the above may result in serious injury or even death.

    SKU: 11436
    $472.50
    Add to cart