REAR COUNTERWEIGHT, 13B 74-85 RX7

Related Products:

• 

  ENGINE FRONT COVER, THRUST BEARING 70-92

  

  Front Engine Cover, Thrust Bearing 70-92
  Two needed per engine

  SKU:	11-505B-0813
  Manufacturer SKU:	0813-11-505B

  $30.14
  Add to cart
• 

  FLYWHEEL STEEL, 83-92 RX7 NON TURBO NO COUNTERWEIGHT

  Steel Flywheel, 83-92 Non Turbo
  Does NOT include Counterweight!!

  Applications
  Designed to retain enough mass for comfortable standing starts this Racing Beat flywheel is ideal for street use, yet it is sufficiently lighter to afford a noticeable improvement in low speed acceleration and to make shifting much smoother. For street use our lightweight steel flywheel not only allows the engine to accelerate more rapidly, but it also eliminates much of the rubbery feel that occurs at clutch engagement while shifting.  

  Precision Machining
  Precision CNC-machined from high strength steel, our flywheel assembly is mated to the Mazda OEM ring gear, then surfaced hardened using a ferritic carburizing heat-treating process, creating an extremely durable disc wear surface. The ring gear is thermally-mated to the flywheel and bolted in place for added security to prevent slippage during engagement of the starter motor.

  Weight Comparison
  The weight of the stock flywheel is 23 lbs., compared to 13 lbs for the Racing Beat Lightweight Steel Flywheel. The actual reduction in inertia from stock is much greater than the weights suggest, since the stock flywheel is 1 to 2 inches thick at its outside edge.

  Retaining Critical Engine Balance
  The installation of an aftermarket flywheel requires the use of a Mazda rear counterweight unit to ensure critical balance of the internal rotating assembly (engine rotors). As produced by Mazda, the original stock rotary flywheel features a pronounced balancing mass included in the flywheel casting. This balancing mass, combined with the stock front counterweight unit, provides the correct balance required for the optimal rotational operation of the engine rotors.

  To allow an aftermarket flywheel to be used on several different rotary engine applications, this balancing mass is eliminated from the design of the rotary flywheel. However, this critical balancing mass must be replaced with an alternative balance weight or risk severe engine damage due to an “unbalanced” engine. A convenient alternative is to install an appropriate rear counterweight from an automatic transmission-equipped RX-7.

  Rear Counterweight (Required)
  All Racing Beat flywheels require the use of an automatic transmission rear counterweight for correct operation. This required Mazda rear counterweight can be ordered separately as needed.

  Installation Hardware
  Racing Beat Flywheel kits include the flywheel unit and the appropriate mounting hardware, which includes the appropriate tensile-strength hardware to attach the pressure plate to the flywheel.  DO NOT use other aftermarket flywheel mounting kits with the Racing Beat flywheels.

  We strongly recommend replacing the throwout bearing during any clutch work to ensure trouble free performance. Also, we recommend replacing the transmission front and rear seal kit when re-installing the transmission to reduce the possibility of leakage.

  Safety Warning
  None of the flywheel or clutch components shown in this site should ever be allowed to exceed 10,500 RPM under any condition. This same RPM limit applies to stock components. You must use an engine RPM-limiter to prevent excessive RPM. If your engine is capable of exceeding 8,500 RPM you must install a transmission scatter shield, or ballistic blanket. Failure to implement the above may result in serious injury or even death.

  SKU:

  11437

  $472.50
  Add to cart
• 

  PULLEY ECCENTRIC, 79-92 2 BELT ALUMINUM

  Racing Beat 2 Belt Aluminum Eccentric Pulley, 79-92 

  O.D.: 3 7/8″

  The Racing Beat Aluminum Double Sheave Main Drive Pulley for virtually all 1974-92 12A and 13B engines is designed for high performance/RPM street and moderate racing use, slowing the water pump and alternator 13-15 %, thereby reducing cavitation and power loss. If used with our Aluminum Alternator Double Sheave Pulley, you can have a true dual belt system. The stock air conditioning pulley is accommodated. Timing marks are provided at 10 degrees ATC,  0 degrees (TDC), 10 degrees BTC, and 20 degrees BTC. The weight of this pulley is 16 oz.

  We do not recommend this underdrive pulley be installed on “street” driven cars that are used for stop-and-go driving. In addition, we do not recommend the use of this underdrive pulley on 1987-91 RX-7 Turbo II engines unless modifications have been made (shorter intake runners, etc..) to increase the engine’s RPM range substantially. Turbo II engines produce their peak power in a lower RPM range, relative to a non-turbo engine.

  Note: It is not practical to offer a standard replacement belt due to the variations in engine configurations. After measuring the distance required for your application, we suggest you contact your local auto parts store to obtain the required 3/8-inch wide replacement belt.

  SKU:

  11469

  $118.43
  Add to cart
• 

  FLYWHEEL STOPPER TOOL ALL N/A diameter flywheels

  Flywheel Stopper Tool, All Non-Turbo diameter flywheels (Except RX-8’s)

  Flywheel stopper makes getting the flywheel / counterweight nut off a LOT easier.
  For flywheels 11 3/4″ diameter.

  SKU:	49-220NT
  Manufacturer SKU:	49-220NT

  $23.86
  Add to cart
• 

  PULLEY ECCENTRIC, SINGLE BELT ALUMINUM

  Racing Beat Aluminum Single Belt Eccentric Pulley 74-92

  O.D.: 3 7/32″

  SKU:

  11473

  $91.69
  Add to cart
• 

  FRONT COUNTERWEIGHT, —NLA— 13B 74-85

  

  FRONT COUNTERWEIGHT,  13B 74-85

  Sorry, this item has been discontinued by Mazda.

  We sell used Counterweights on our Ebay Store (Mazdatrix1)

  SKU:	11-5110-N304
  Manufacturer SKU:	N304-11-511

  $0.00
  Read more