HEATSHIELD, 74-95 ALL 12A & 13B

HEATSHIELD, 74-95 ALL 12A & 13B

Heatshield, 74-95 All 12A & 13B

Click Here for a Weber 48IDA Suggested Parts List

Browse our Weber Carbs, Manifolds and Parts section

SKU: 16219

HEATSHIELD, 74-95 ALL 12A & 13B

Intake Manifold/Header Heat Shield – 12A & 13B- 1974-95 All Models – Racing Beat’s Header Heat Shield Assembly effectively reduces intake manifold and carburetor temperatures by reflecting the heat radiating from the header away from both the intake manifold and the carburetor. Reducing intake manifold and carburetor temperatures both allows the engine to produce more horsepower and reduces the likelihood of fuel “boiling” in the carburetor float bowl(s) once the engine is shut off.

The Header Heat Shield is intended for use with Racing Beat’s Holley and Weber Down Draft carburetor manifolds as well as Racing Beat’s Dellorto Side Draft “bottom-half” carburetor manifold assemblies. The Header Heat Shield is also compatible with many of Mazda’s Factory rotary carburetor manifolds.

The Header Heat Shield Assembly is specifically not compatible with the Mazda Factory 6-Port manifolds delivered on the 1984-1992 13B, 6-Port, fuel injected engines.

$109.15

Related Products:

  • WEBER FLOAT NEEDLE IDA, 3.0 MM

    WEBER FLOAT NEEDLE IDA, 3.0 MM

    Weber Float Needle IDA, 3.0 mm
    Rotary engines using IDA carbs need the largest float needle you can find. This 3.0 is the largest currently avialable. 

    Weber IDA Float Needle Crush Washer

    Click Here for a Weber 48IDA Suggested Parts List

    Browse our Weber Carbs, Manifolds and Parts section

    SKU: 79504.300
    $25.00
    Add to cart
  • MANIFOLD HOLLEY, 13B 87-92 TURBO

    MANIFOLD HOLLEY, 13B 87-92 TURBO

    Holley Manifold, 13B 87-92 Turbo II

    The Racing Beat-designed intake manifold for the 1987-91 TURBO II engine is ideally suited to meet the performance requirements of the Holley carburetor. Designed by Chief Engineer/Engine Builder Jim Mederer, these cast aluminum intake manifolds have proven themselves in a variety of street and race applications.

    All of Racing Beat’s manifolds for Holley carburetor applications are sand-cast by a local foundries and delivered to our in-house production shop for all machining and surface finishing processes. Select manifolds are then hand-ported to match a specific intake port configuration for an intended engine application. Further machining is then undertaken to match the base-plate surface to the Holley carburetor base. These critical machining steps ensure a positive fitment between both the engine surface and the carburetor base. Every manifold is then surface finished using a ball-burnishing process that enhances the final appearance of the aluminum material. Once these labor-intensive processes have been completed these manifolds look as good as they perform!

    SKU: 16475
    $406.28
    Add to cart
  • MANIFOLD HOLLEY, 79-85 12A

    MANIFOLD HOLLEY, 79-85 12A

    Holley Manifold, 79-85 12A Stock port

    The Racing Beat-designed intake manifold for the 1979-85 12A Stock and Street-ported engine is ideally suited to meet the performance requirements of the Holley carburetor. Designed by Chief Engineer/Engine Builder Jim Mederer, these cast aluminum intake manifolds have proven themselves in a variety of street and race applications.

    All of Racing Beat’s rotary engine manifolds for Holley carburetor applications are sand-cast by a local foundry and delivered to our in-house production shop for all machining and surface finishing processes. All Racing Beat intake manifolds are hand-ported to match a specific intake port configuration for the intended engine application. Further machining is then undertaken to match the base-plate surface to the Holley carburetor base. These critical machining steps ensure a positive fitment between both the engine surface and the carburetor base. Every intake manifold is then surface finished using a ball-burnishing process that enhances the final appearance of the aluminum material. Once these labor-intensive processes have been completed these manifolds look as good as they perform!

    This manifold includes a vacuum source for power brakes. If needed, an engine-to-manifold gasket (79-80) or (81-85), and/or Holley base gasket are available separately.

    SKU: 16464
    $406.28
    Add to cart
  • WEBER MANIFOLD 48 IDA

    WEBER MANIFOLD for 12A with a 48IDA

    Weber Manifold for 12A with a 48IDA
    DOES NOT come with the intake manifold gasket

    Click Here for a Weber 48IDA Suggested Parts List

    Browse our Weber Carbs, Manifolds and Parts section

    SKU: 16482
    $479.04
    Add to cart
  • WEBER IDA MANIFOLD for 86-92 TURBO Engines

    WEBER IDA MANIFOLD for 86-92 TURBO Engines

    Racing Beat Weber IDA Manifold for 86-92 Turbo Engines

    Note: This manifold does NOT have any hole or fitting for the brake servo hose.
    If you want to use the servo then drill and tap a 1/8 NPT (pipe thread) hole somewhere convenient in the rear manifold runner (PRIOR to installation).
    Use a straight or 90 degree 5/16″ (8mm) fitting.

    Click Here for a Weber 48IDA Suggested Parts List

    Browse our Weber Carbs, Manifolds and Parts section

    SKU: 16494
    $395.36
    Add to cart
  • FILTER AIR CANISTER, 48 IDA WITH K&N SHORT

    FILTER AIR CANISTER, 48 IDA WITH K&N SHORT

    Air Canister Filter for 48 IDA With K&N Short Filter

    Click Here for a Weber 48IDA Suggested Parts List

    Browse our Weber Carbs, Manifolds and Parts section

    SKU: 56-1210
    $156.89
    Add to cart

You May Also Like:

  • AIR FILTER HOUSING RACING BEAT HOLLEY W/O FILTER

    AIR FILTER HOUSING, RACING BEAT HOLLEY WITHOUT FILTER

    Racing Beat Air Filter Housing Without Filter for Racing Beat Holley Carburetor

    Racing Beat’s dyno-proven Power Pulse Air Filter Assembly, for the Holley Carburetor, is designed specifically for performance. While the assembly uses the same Racing Beat foam air filter element that fits the stock canister, the design of the Power Pulse canister both improves air flow into the carburetor and limits the introduction of dirt particles into the filter element. The spun aluminum canister pieces are powder-coated white for added durability.

    The Power Pulse Air Filter Assembly fits most Holley 465, 550, 600, and 650 CFM carburetors (specifically, all Racing Beat Holley Intake System Kits). There is no provision for emission control valve hose/air pump hose connections on this assembly; however, there is a position available to connect a crankcase breather tube if needed.

    SKU: 16530
    $109.15
    Add to cart
  • AIR FILTER HOUSING, RACING BEAT STOCK W/O FILTER

    AIR FILTER HOUSING, RACING BEAT STOCK WITHOUT FILTER

    Racing Beat Air Filter Housing, Stock without Filter

    Racing Beat’s dyno-proven Power Pulse Air Filter Assembly, for all 1971-85 Stock Carburetor Bodies, is designed specifically for performance. While the assembly uses the same Racing Beat foam air filter element that fits the stock canister, the design of the Power Pulse canister both improves air flow into the carburetor and limits the introduction of dirt particles into the filter element. The spun aluminum canister pieces are powder-coated white for added durability.

    There is no provision for emission control valve hose/air pump hose connections on this assembly; however, there is a position available to connect a crankcase breather tube if needed.

    SKU: 16531
    $109.15
    Add to cart