2004
General Hardware
-
-10 CAP PLASTIC, FITS -10 MALE END
-10 Plastic Cap, Fits -10 Male End
Plastic Cap for male end
These come in very handy when you are removing the engine or cooler, to prevent debris from getting in.
SKU: -10-CAP -
-10 HOSE END 45 DEGREE, TUBE
-10 Hose End 45 Degree, Tube 45 Degree
There are some custom applications where the available oil cooler line sets will just not work, and special length lines need to be assembled. We carry -10 ends in either straight, 45 degree, or 90 degree, as well as -10 hose.SKU: -10-END-45 -
-10 HOSE END 90 DEGREE, TUBE 90 DEGREE
-10 Hose End 90 Degree, Tube 90 Degree
There are some custom applications where the available oil cooler line sets will just not work, and special length lines need to be assembled. We carry -10 ends in either straight, 45 degree, or 90 degree, as well as -10 hose.SKU: -10-END-90 -
-10 HOSE END, STRAIGHT
-10 Hose End, Straight
There are some custom applications where the available oil cooler line sets will just not work, and special length lines need to be assembled. We carry -10 ends in either straight, 45 degree, or 90 degree, as well as -10 hose.SKU: -10-END -
-10 PLUG PLASTIC, FITS -10 FEMALE END
-10 Plastic Plug, Fits -10 Female End
These come in very handy when you are removing the engine or cooler, to prevent debris from getting in, and oil from leaking out.
SKU: -10-PLUG -
10MM CRUSH WASHER 74-11 WATER DRAIN ETC
Water Drain Plug Crush Washer 10mm 74-11
SKU: 41-0000-9956 Manufacturer SKU: 9956-41-000 -
ADAPTER WATER TEMPERATURE, 3/8 NPT TO MECHANICAL TEMPERATURE GAUGE
Water Temperature, 3/8 NPT To Mechanical Temperature Gauge Adapter
SKU: 2263 -
BATTERY HOLD DOWN, NUT 6MM BIG FLANGE
Battery Hold Down Nut, 6mm Big Flange
SKU: 00-603B-9994 Manufacturer SKU: 9994-00-603B -
BOLT FLEXPLATE RX8, FLEXPLATE TO COUNTERWEIGHT
Flexplate To Counterweight Bolt RX8
SKU: 41-0350-9978 Manufacturer SKU: 9978-41-035 -
BOLT FRONT PULLEY, 04-11 RENESIS OEM
OEM Front Pulley Bolt, 04-11 Renesis
SKU: 11-4060-N3H1 Manufacturer SKU: N3H1-11-406 -
CLUTCH HARDWARE FOR RACE 7.25″ RALLY TWIN
Race Clutch Hardware for 7.25″ Rally Twin
SKU: 298063RY-HW-725 -
CLUTCH RACE HARDWARE, FOR 5.5″ DOUBLE DISC
Race Clutch Hardware, For 5.5″ Double Disc Race Clutches using our Race Flywheels
SKU: 284063-HW-5.5 -
CLUTCH RACE HARDWARE, FOR 7.25″ TWIN DISC
Race Clutch Hardware, For use with 7.25″ Twin disc Clutches using our Race Flywheels
SKU: 298062-HW-725 -
DOWEL PIN SHORT, FRONT COVER & BELLHOUSING
Front Cover and Bellhousing Short Dowel Pin
SKU: 10-3090-1757 Manufacturer SKU: 1757-10-309 -
DRY SUMP ADAPTER #1, ALUMINUM AN -12
Aluminum AN Dry Sump Adapter #1, -12
SKU: 14-R960-ZR03 Manufacturer SKU: ZR03-14-R96 -
DRY SUMP ADAPTER #2, ALUMINUM AN -16
Aluminum Dry Sump Adapter #2, AN -16
SKU: 14-R980-ZR03 Manufacturer SKU: ZR03-14-R98 -
FLYWHEEL HARDWARE, STEEL 74-92,TURBO, RACE
Steel Flywheel Hardware Kit, 74-92, Turbo, Race
Flywheel to Counterweight Bolt SetSKU: 95179 -
FREEZE PLUG LARGE, ALL FRONT & REAR HOUSING
1 3/16″ diameter Mazda OEM freeze plug for the larger holes front and rear side housings.
( uses 6-7 depending on year)
SKU: 63-0000-9930 Manufacturer SKU: 9930-63-000 -
FREEZE PLUG SMALL, FRONT HOUSING
Freeze Plug Small (3/4″ Diameter), Front Housing
(for front side housing, uses 1)SKU: 62-0000-9930 Manufacturer SKU: 9930-62-000 -
FUEL DOOR BUMP STOP, 81-85 RX7, 93-95 RX7, & 04-11 RX8
Fuel Door Bump Stop (Two per Vehicle)
Fits 81-85 RX7
93-95 RX7
04-11 RX8SKU: 70-4910-0187 Manufacturer SKU: 0187-70-491 -
HYLOMAR TUBE, 1.5 OZ
Best chemical we have found for water seal O-rings. Brush it on with a trimmed down “acid” brush – in the water seal grooves and then on the seals after you have placed them into the grooves. Stays tacky for a LONG time.
One tube will do one engine easily.
SKU: HYLOMAR -
OIL HOSE FITTING, 93-95 & 04-11, END WITH CLIP
Oil Hose Fitting, 93-95 & 04-11, End With Clip
SKU: 14-850A-N3G1 Manufacturer SKU: N3G1-14-850A -
OIL HOSE RETAINING CLIP, SUPERSEDED USE N3G1-14-850A
This item has been superseded. Now use N3G1-14-850A
SKU: 14-6220-N3A1 Manufacturer SKU: N3A1-14-622 -
OIL PAN BOLT SET —NLA — (FOR ALL 2-ROTOR ENGINES) 22 – BOLTS
Sorry, no longer available.
Oil Pan Bolt Set (For All 2-Rotor Engines) 22 – BoltsSKU: OIL-PAN-BOLT-SET -
Plug Oil Injector Hole (rotor housings + intake manifold)
Plug for plugging oil injector holes (rotor housings + intake manifold) when they are not being used. Sold EACH, you typically need 2 or 4 depending what you are doing. Fits all oil injector holes from 84-11. Supplied with sealing washer. Uses 3/16 allen wrench.
SKU: 19-064A-FT01-RT Manufacturer SKU: FT01-19-064A-RT -
POWERPLANT FRAME TAPER BOLT 93-11
Powerplant Frame Taper Bolt 93-11
SKU: 39-0660-FD01 Manufacturer SKU: FD01-39-066 -
RIVET PLASTIC 86-ON, PUSH BUTTON TYPE -NLA-
This item has been discontinued by Mazda
Plastic Push Button Type Rivet, 86-On
SKU: 56-81X0-FB01 Manufacturer SKU: FB01-56-81X -
RIVET PLASTIC, FAN SHROUD LOWER
Plastic Rivet, Fan Shroud, Lower
SKU: 40-6580-9926 Manufacturer SKU: 9926-40-658 -
SCREW BRAKE ROTOR, ALL YEARS (EACH)
Brake Rotor Screw, All Years, Phillips Flat Head, Counter Sunk
Sold individuallySKU: 10-8200-9983 Manufacturer SKU: 9983-10-820 -
WEBER IDLE SPEED SCREW
Weber Idle Speed Screw
Spring is not included. It is 47600.007Browse our Weber Carbs, Manifolds and Parts section
SKU: 64625.012 -
WEBER INLET FITTING for 8mm (5/16″) push on hose
Weber 12mm Inlet Fitting for a regular 5/16″ rubber hose.
All Weber IDA carbs come with a useless banjo fitting we have never figured out how to use (unless you tap it 1/8-pipe and use a “barb” fitting). This will replace the stock inlet fitting with a hose nipple that you can push on and clamp regular fuel hose to. This is the stock fuel hose size for all Mazda RX cars.
Click Here for a Weber 48IDA Suggested Parts List
Browse our Weber Carbs, Manifolds and Parts section
SKU: 99301.380 Manufacturer SKU: 99301.380 -
WEBER INLET FITTING, AN -6 TO WEBER 12MM
-6 To Weber 12mm Inlet Fitting
All Weber IDA carbs come with a useless banjo fitting we have never figured out how to use (unless you tap it 1/8-pipe and use a “barb” fitting). This will replace the stock inlet fitting with -6AN so you can use braided hose.
The 12mm Stat-O-Seal is strongly recommended for this fitting — it is at: WEBER INLET SEAL, STAT-O-SEAL FOR 12MM
We also have a 90° fitting for 8mm / 5/16″ push on hose at: WEBER INLET FITTING for 8mm (5/16″) push on hoseClick Here for a Weber 48IDA Suggested Parts List
Browse our Weber Carbs, Manifolds and Parts section
SKU: 30606-M12D -
WEBER INLET SEAL, STAT-O-SEAL FOR 12MM
Weber Inlet Seal, Stat-O-Seal FOR 12mm
This is the seal needed for the -6AN fuel inlet fitting for Weber carbs.Click Here for a Weber 48IDA Suggested Parts List
Browse our Weber Carbs, Manifolds and Parts section
SKU: 357-12MM-STAT -
WEBER NUT 8X1.25 WITH 10MM HEX
Weber Nut 8X1.25 With 10mm Hex
These are needed for the larger bore carbs as there is not enough room to get a 12mm wrench correctly on the base nuts.
These use a 10mm wrench which gives you room to tighten the nut.
Hard to find in “not jet nut” style and in steel. They can come in handy in many other places also.Click Here for a Weber 48IDA Suggested Parts List
Browse our Weber Carbs, Manifolds and Parts section
SKU: 967-NUT -
WEBER SHAFT LEVER, WITH STOP PIN LEFT
Weber Shaft Lever, With Stop Pin Left. 14ga steel
We have these “stops” made for us so the throttle STOP is on the same side of the carb as the throttle PULL. Adjusted correctly this prevents the throttle shaft from being bent when full throttle is applied.Click Here for a Weber 48IDA Suggested Parts List
Browse our Weber Carbs, Manifolds and Parts section
SKU: MAT460-L -
WEBER SHAFT LEVER, WITH STOP PIN RIGHT
Weber Shaft Lever, With Stop Pin Right
This STOP is for when the carb fuel inlet is on the Engine side, cable pulling from ABOVE the shaft.
These are for what we call “Australian Style” manifolds.Browse our Weber Carbs, Manifolds and Parts section
SKU: MAT460-R -
WEBER SHAFT LOCK TAB
Weber Shaft Lock Tab Washer Fits IDA or DCOE Sold Each
Part can be referenced at #26
Browse our Weber Carbs, Manifolds and Parts section
SKU: 55520.004 Manufacturer SKU: 55520.004 -
WEBER SHAFT NUT
Weber Shaft Nut Fits IDA or DCOE Sold Each
Part can be referenced at #25
Browse our Weber Carbs, Manifolds and Parts section
SKU: 34710.003 -
WEBER SHAFT WASHER
Weber Shaft Washer Fits IDA or DCOE Sold Each
Reference part at #27
Browse our Weber Carbs, Manifolds and Parts section
SKU: 99024.258 -
WEBER SPRING for EITHER IDLE SPEED OR MIXTURE SCREW
Weber Spring for Either Idle Speed or Mixture Screw
Browse our Weber Carbs, Manifolds and Parts section
SKU: 47600.007 -
WEBER STUD, 8X1.25 35MM
Weber Stud, 8X1.25 35mm
Click Here for a Weber 48IDA Suggested Parts List
Browse our Weber Carbs, Manifolds and Parts section
SKU: AV11981 -
WEBER STUD, 8X1.25 45MM
Weber Stud, 8X1.25 45mm
Most of the Weber Manifolds do not include studs to hold the carb to the manifold. These 45mm ones work great when you are using spacers — measure to be sure these are what you need – depends on the spacer thickness.Browse our Weber Carbs, Manifolds and Parts section
SKU: AV11983