1971
Engine
-
BOLT FRONT PULLEY, —NLA— ALL-85 OEM
BOLT FRONT PULLEY, ALL-85 OEM
Sorry, this item has been discontinued by Mazda.
SKU: 11-611B-0820 Manufacturer SKU: 0820-11-611B -
Eccentric Shaft Oil Jet – .200 – COMPETITION
Eccentric Shaft Oil Jet – .200 – Competition
This oil jet replaces the factory checkball and spring.
SKU: 11-4110-8553 Manufacturer SKU: 8553-11-411 -
ENGINE DOWEL PIN, 12A ALL
Engine Dowel Pin, 12A All
Mazda has discontinued this item. We still have 2 left.SKU: 10-111B-0839 Manufacturer SKU: 0839-10-111B -
ENGINE FRONT COVER, BEARING PLATE 70-92
Engine Front Cover, Bearing Plate 70-92
SKU: 11-5010-1011 Manufacturer SKU: 1011-11-501 -
ENGINE FRONT COVER, FRONT BOLT WASHER
Front Engine Cover, Front Hub Bolt Crush Washer
SKU: 22-8000-9956 Manufacturer SKU: 9956-22-800 -
ENGINE FRONT COVER, OIL PUMP KEY
Oil Pump Key, Engine Front Cover
SKU: 14-119B-0839 Manufacturer SKU: 0839-14-119B -
ENGINE FRONT COVER, THRUST BEARING 70-92
Front Engine Cover, Thrust Bearing 70-92
Two needed per engineSKU: 11-505B-0813 Manufacturer SKU: 0813-11-505B -
ENGINE FRONT COVER, THRUST PLATE 70-92
Front Engine Cover, Thrust Plate 70-92
SKU: 11-5040-1011 Manufacturer SKU: 1011-11-504 -
ENGINE FRONT COVER, THRUST WASHER 70-92
Front Engine Cover, Thrust Washer 70-92
This is the thin one that sits inside the front counterweight.SKU: 11-5070-1011 Manufacturer SKU: 1011-11-507 -
FREEZE PLUG LARGE, ALL FRONT & REAR HOUSING
1 3/16″ diameter Mazda OEM freeze plug for the larger holes front and rear side housings.
( uses 6-7 depending on year)
SKU: 63-0000-9930 Manufacturer SKU: 9930-63-000 -
FREEZE PLUG SMALL, FRONT HOUSING
Freeze Plug Small (3/4″ Diameter), Front Housing
(for front side housing, uses 1)SKU: 62-0000-9930 Manufacturer SKU: 9930-62-000 -
HOSE OIL METERING, 72-85 CARB PER FOOT
Oil Metering Hose, 72-85, Carb., PER FOOT
We have found this hose to work well for the oil metering lines for early cars that do not use fittings on the line ends. This hose can be used stand-alone, it will push directly onto the nipples at the carb and the metering pump, OR it can be used to splice an OEM metering hose by pushing over the OEM plastic hose.
At this time the 12A OEM short hose is only one available for carbs. We typically will use two short OEM lines and cut one and extend it about two inches in the middle with this hose to make a long line.
This hose also works well to splice/repair any OEM injector line for all 70-11 rotary.
Sold by the foot.SKU: MOPHOSE-1 -
HYLOMAR TUBE, 1.5 OZ
HYLOMAR TUBE, 1.5 OZ
Best chemical we have found for water seal O-rings. Brush it on with a trimmed down “acid” brush – in the water seal grooves and then on the seals after you have placed them into the grooves. Stays tacky for a LONG time.
One tube will do one engine easily.
SKU: HYLOMAR -
O-RING DOWEL PIN, ALL ROTARY
Dowel Pin, O-Ring All Rotary
SKU: 10-B730-N3A1 Manufacturer SKU: N3A1-10-B73 -
O-RING OIL CAP, ALL OEM 70-08
OEM Oil Cap O-Ring, All 70-08
SKU: 10-2520-8871 Manufacturer SKU: 8871-10-252 -
OIL BLOCK BYPASS, WHEN USING REMOTE
OIL BLOCK BYPASS, WHEN USING REMOTE
This block is designed to facilitate the installation of a remote oil filter assembly. Machined from aluminum-alloy with an internal passage that eliminates the need for the stock oil filter, this component is very popular for customized engine and racing applications.
SKU: 11822 -
-
OIL DRAIN PLUG WASHER, ALL ROTARY 14mm Aluminum
Oil Drain Plug Washer, All Rotary 14mm Aluminum. For Copper click here
SKU: 41-4000-9956 Manufacturer SKU: 9956-41-400 -