INJECTOR LOWER GROMMET, 93-95 SECONDARY
Secondary Lower Injector Grommet, 93-95
| SKU: | 13-257A-NF01 |
| Manufacturer SKU: | NF01-13-257A |
INJECTOR LOWER GROMMET, 93-95 SECONDARY
Injector Grommets are the thick seal at the base of the injector and the dust seal at the top.
$9.06
Related Products:
-
-
INJECTOR O-RING, 93-95 UPPER
Upper Injector O-Ring, 93-95
SKU: 13-ZG40-NF01 Manufacturer SKU: NF01-13-ZG4 -
INJECTOR O-RING, 93-95 LOWER
Injector Lower O-Ring, 93-95
SKU: 13-ZG30-NF01 Manufacturer SKU: NF01-13-ZG3 -
INJECTOR AIR BLEED SECONDARY, 93-95
Secondary Air Bleed Injector, 93-95
Note: Air bleeds are the little plastic diffusers that go in the hole under the injector. 84-88 non turbos use a one piece bleed, while 86-88 turbo and all 89-92 use a two piece bleed (Top & Bottom). These pieces almost always break when removed from the engine. Air bleeds are supplied with their O-rings installed.
SKU: 13-C600-N3A1 Manufacturer SKU: N3A1-13-C60 -
INJECTOR LOWER GROMMET, 93-95 PRIMARY
Primary Lower Injector Grommet, 93-95
SKU: 13-2570-N3A1 Manufacturer SKU: N3A1-13-257 -
INJECTOR AIR BLEED O-RING, 84-95 ALL
Air Bleed Injector O-Ring, 84-95 All
SKU: 10-1252-9954 Manufacturer SKU: 9954-10-1252
You May Also Like:
-
VALVE AIR CONTROL, CHECK VALVE- ALL
Check Valve for All Air Control Valves
SKU: 13-7300-1480 Manufacturer SKU: 1480-13-730 -
WEBER MANIFOLD for PERIPHERAL PORT 13B 48 or 51IDA RACING BEAT PERIPHERAL PORT HOUSING
Weber Manifold for Peripheral Port 13B 48 or 51IDA
This manifold is designed to fit the Racing Beat Periperal Port 13B Rotor Housings.Works with IDA carbs from 48mm to 52mm bore.
The Racing Beat-designed and manufactured Peripheral Port Intake Manifold mates a Weber 48 IDA or 51 IDA downdraft carburetor, or equivalent throttle body, to the Racing Beat-manufactured 13B peripheral port housings. (This manifold cannot be used on the Mazda Factory Race MFR housings.) The steel tubing manifold is attached to the rotor housings with hoses that are included. A simple support bracket fabricated for your particular application, typically attached from the carburetor-manifold junction to the threaded bosses on top of the rotor housings, will complete the task.
Browse our Weber Carbs, Manifolds and Parts section
SKU: 16490 -
AIR FILTER FOAM, 79-85 CARBURETED
Foam Air Filter for Carbs 79-85
The Racing Beat-designed Foam Air Filter Element for all 1971-85 Rotaries (except 1984-85 GSL-SE) consists of a polyurethane foam over a metal screen form that interchanges exactly with the stock element. The foam element can be re-used by periodically cleaning in solvent and re-oiling. While the element offers no significant increase in air flow when compared to a clean, stock paper element, as the paper element collects dirt its air flow capacity decreases dramatically while the foam element is nearly unaffected.
SKU: 16510 -
WEBER IDA IDLE JET HOLDER 120
Weber IDA Idle Jet Holder 120
Browse our Weber Carbs, Manifolds and Parts section
SKU: 77903.120 -
BPAV GASKET, 86-88 ALL
Bypass Air Control Valve Gasket 86-88 All
SKU: 20-661A-N326 Manufacturer SKU: N326-20-661A -
VALVE BPAV, 86-88 NON-TURBO
By Pass Air Valve, 86-88 Non-Turbo
SKU: 20-6600-N326 Manufacturer SKU: N326-20-660