INTAKE MANIFOLD GASKET, 86-88 TURBO
Intake Manifold Gasket, 86-88 Turbo
| SKU: | 13-111D-N318 |
| Manufacturer SKU: | N318-13-111D |
INTAKE MANIFOLD GASKET, 86-88 TURBO
$15.83
Related Products:
-
INTAKE MANIFOLD CENTER GASKET, 86-88 TURBO
Intake Manifold Center Gasket, 86-88 Turbo
Between Upper and Lower Manifolds
SKU: 13-112A-N318 Manufacturer SKU: N318-13-112A -
GASKET SET, RX7 86-88 TURBO —NLA—
This set is discontinued by Mazda
Gasket Set, RX7 86-88 Turbo
SKU: 10-2710-8DF4 Manufacturer SKU: 8DF4-10-271 -
GASKET SET 86-88 TURBO, O-RINGS ONLY
Gasket Set 86-88 Turbo, O-Rings Only
SKU: 10-S60A-N318 Manufacturer SKU: N318-10-S60A -
HYLOMAR TUBE, 1.5 OZ
HYLOMAR TUBE, 1.5 OZ
Best chemical we have found for water seal O-rings. Brush it on with a trimmed down “acid” brush – in the water seal grooves and then on the seals after you have placed them into the grooves. Stays tacky for a LONG time.
One tube will do one engine easily.
SKU: HYLOMAR -
O-RING THROTTLE BODY TO INLET PIPE 86-92
Throttle Body to Inlet Pipe O-Ring 86-92
SKU: 13-W690-N326 Manufacturer SKU: N326-13-W69 -
WATER JACKET O-RING for Intake Manifold
Water Jacket O-Ring for Intake Manifold
We tested / looked at aftermarket O-rings but never found any that worked as well as these Mazda OEM ones.
We recommend using new ones anytime you are installing your intake manifold.
Needed on 1970 – 1992 non-6-port engines. This includes all the 86-92 Turbo rotor housings in case you are using those in another engine combo.
SKU: 13-1130-8527 Manufacturer SKU: 8527-13-113
You May Also Like:
-
AIR FILTER HOUSING, RACING BEAT HOLLEY WITHOUT FILTER
Racing Beat Air Filter Housing Without Filter for Racing Beat Holley Carburetor
Racing Beat’s dyno-proven Power Pulse Air Filter Assembly, for the Holley Carburetor, is designed specifically for performance. While the assembly uses the same Racing Beat foam air filter element that fits the stock canister, the design of the Power Pulse canister both improves air flow into the carburetor and limits the introduction of dirt particles into the filter element. The spun aluminum canister pieces are powder-coated white for added durability.
The Power Pulse Air Filter Assembly fits most Holley 465, 550, 600, and 650 CFM carburetors (specifically, all Racing Beat Holley Intake System Kits). There is no provision for emission control valve hose/air pump hose connections on this assembly; however, there is a position available to connect a crankcase breather tube if needed.
SKU: 16530 -
SOLENOID TURBO CONTROL, 93-95 ON RACK
Turbo Control Solenoid, 93-95 On Rack
SKU: 18-7410-N390 Manufacturer SKU: N390-18-741 -
VALVE BPAV, 86-88 NON-TURBO
By Pass Air Valve, 86-88 Non-Turbo
SKU: 20-6600-N326 Manufacturer SKU: N326-20-660 -
VALVE VACUUM 1-WAY, 93-95 ALL METAL
1-Way Vacuum Valve, 93-95 All Metal
SKU: 13-8900-NF01 Manufacturer SKU: NF01-13-890 -
WEBER IDA IDLE JET HOLDER 120
Weber IDA Idle Jet Holder 120
Browse our Weber Carbs, Manifolds and Parts section
SKU: 77903.120 -
PURGE VALVE, 79-92—NLA—
Purge Valve, 79-92
Sorry, this item has been discontinued by Mazda
SKU: 20-950A-1480 Manufacturer SKU: 1480-20-950A