INTAKE MANIFOLD GASKET, 04-11 RENESIS 4 PORT
Intake Manifold Gasket, 04-11 Renesis 4 Port
| SKU: | 13-1110-N3H1 |
| Manufacturer SKU: | N3H1-13-111 |
INTAKE MANIFOLD GASKET, 04-11 RENESIS 4 PORT
$51.94
Related Products:
-
GASKET SET 04-11, O-RINGS ONLY
Gasket Set 04-11 RX8, O-Rings Only
SKU: 10-S60A-N3Z1 Manufacturer SKU: N3Z1-10-S60A -
THROTTLE BODY GASKET, 04-11 ORANGE O-RING
Throttle Body Gasket, 04-11 Orange O-Ring
Throttle Body to Upper Intake Manifold
SKU: 13-655A-N3H1 Manufacturer SKU: N3H1-13-655A -
INTAKE MANIFOLD CENTER GASKET, 04-11 SMALL ROUND USES 3
Intake Manifold Center Gasket, 04-11 Small Round
Uses 3SKU: 13-1120-N3H6 Manufacturer SKU: N3H6-13-112 -
HYLOMAR TUBE, 1.5 OZ
HYLOMAR TUBE, 1.5 OZ
Best chemical we have found for water seal O-rings. Brush it on with a trimmed down “acid” brush – in the water seal grooves and then on the seals after you have placed them into the grooves. Stays tacky for a LONG time.
One tube will do one engine easily.
SKU: HYLOMAR -
INTAKE MANIFOLD CENTER GASKET 04-11 OVAL RING USES 2
Intake Manifold Center Gasket, 04-11 Oval Ring
Uses 2SKU: 13-112A-N3H4 Manufacturer SKU: N3H4-13-112A -
GASKET SET, RX8 04-08 A/T 4-PORT
GASKET SET, RX8 04-08 A/T 4-PORT
This kit contains all exterior gaskets.
You must use this O-Ring Gasket Set to assemble the motor.SKU: 10-S50B-N3Z1 Manufacturer SKU: N3Z1-10-S50B
You May Also Like:
-
SOLENOID TURBO CONTROL, 93-95 ON RACK
Turbo Control Solenoid, 93-95 On Rack
SKU: 18-7410-N390 Manufacturer SKU: N390-18-741 -
AIR FILTER K&N, 79-85 EXCEPT GSLSE —NLA—
Sorry, this item has been discontinued by K&N
Air Filter K&N , 79-85 Except GSLSE
SKU: E2700 -
VALVE AIR CONTROL, —NLA— 84-85 SE
VALVE AIR CONTROL, 84-85 SE
Sorry, this item has been discontinued by Mazda.
SKU: 13-720B-N304 Manufacturer SKU: N304-13-720B -
BPAV GASKET, 84-85 GSLSE
Bypass Air Control Valve Gasket 84-85
SKU: 13-7210-N386 Manufacturer SKU: N386-13-721 -
VALVE VACUUM DELAY, GREEN/BLACK
Vacuum Delay Valve Green/Black. Arrow on body points to black end
SKU: 20-3090-8574 Manufacturer SKU: 8574-20-309 -
WEBER MANIFOLD for PERIPHERAL PORT 13B 48 or 51IDA RACING BEAT PERIPHERAL PORT HOUSING
Weber Manifold for Peripheral Port 13B 48 or 51IDA
This manifold is designed to fit the Racing Beat Periperal Port 13B Rotor Housings.Works with IDA carbs from 48mm to 52mm bore.
The Racing Beat-designed and manufactured Peripheral Port Intake Manifold mates a Weber 48 IDA or 51 IDA downdraft carburetor, or equivalent throttle body, to the Racing Beat-manufactured 13B peripheral port housings. (This manifold cannot be used on the Mazda Factory Race MFR housings.) The steel tubing manifold is attached to the rotor housings with hoses that are included. A simple support bracket fabricated for your particular application, typically attached from the carburetor-manifold junction to the threaded bosses on top of the rotor housings, will complete the task.
Browse our Weber Carbs, Manifolds and Parts section
SKU: 16490