FLYWHEEL DOWEL PIN, ALL
Flywheel Dowel Pin, All
Flywheel Dowel Pins have been needed a few times when someone has damaged them, or the machine shop surfacing the flywheel “lost” them.
| SKU: | 30-8220-9923 |
| Manufacturer SKU: | 9923-30-822 |
FLYWHEEL DOWEL PIN, ALL
$5.04
Related Products:
-
FLYWHEEL STOPPER TOOL ALL N/A diameter flywheels
Flywheel Stopper Tool, All Non-Turbo diameter flywheels (Except RX-8’s)
Flywheel stopper makes getting the flywheel / counterweight nut off a LOT easier.
For flywheels 11 3/4″ diameter.SKU: 49-220NT Manufacturer SKU: 49-220NT -
NUT FLYWHEEL, FLYWHEEL/ECCENTRIC
Flywheel Nut, Flywheel/Eccentric Shaft
SKU: 11-711C-0810 Manufacturer SKU: 0810-11-711C -
FLYWHEEL SOCKET TOOL, 54MM IMPACT SOCKET
Flywheel Impact Socket Tool, 54mm, 3/4″ drive
SKU: 49-22009HD -
FLYWHEEL STOPPER TOOL, TURBO, AUTO TRANS AND RX8
Flywheel Stopper Tool, Turbo, Automatic Transmission And RX8 Manual
SKU: 49-220TB Manufacturer SKU: 49-220TB -
-
DOWEL PIN REMOVER TOOL
Dowel Pin Remover Tool
Tool makes pulling the dowels out of the rotor and side housings a piece of cake during engine dis-assembly.
SKU: 49-1290
You May Also Like:
-
BELLHOUSING BOLT, UPPER CENTER & RIGHT 72-92
Upper Center and Upper Right Bell Housing Bolt 72-92 (Sold Each, uses 2)
SKU: 10-8450-8555 Manufacturer SKU: 8555-10-845 -
BELLHOUSING BOLT, LOWER RIGHT 72-92
Lower Right Bell Housing Bolt 72-92
SKU: 41-0400-9978 Manufacturer SKU: 9978-41-040 -
CLUTCH SLAVE HOSE, 04-11 RX8 HARD @ MASTER
Clutch Slave Hardline Hose, 04-11 RX8 @ Master
SKU: 45-510A-FE05 Manufacturer SKU: FE05-45-510A -
TRANSMISSION MOUNT REAR, ALL 74-85 RX7 (EXCEPT 84-85 RX7 AUTO)
Rear Transmission Mount, All 74-85 Except 84-85 Automatic Trans
SKU: 39-340A-1011 Manufacturer SKU: 1011-39-340A -
CLUTCH DISC RACE, ALL ROTARY -82
Racing Beat Race Clutch Disc, All Rotary up to 82, 4 puck
The 4-Puck 215mm Race Clutch Disc is designed for drag and road race use with all 1971-82 12A & 13B Applications (except Rotary Pick-Up). The disc incorporates four (4) sintered copper pucks and a rigid hub for quick, positive engagement, greater fatigue resistance, and improved heat dissipation. The sharpened engagement/disengagement characteristics of this disc require careful driver attention – this disc is not intended for street use.
Time Saving Tip: We strongly recommend replacing the throw-out bearing during any clutch work to ensure trouble free performance. Also, we recommend replacing the transmission front and rear seal kit when re-installing the transmission to reduce the possibility of leakage.
Safety Note: None of the Racing Beat, Exedy, Mazda OE, or any aftermarket flywheel or clutch replacement components should ever be allowed to exceed 10,500 RPM under any condition. You must use an engine RPM-limiter to prevent excessive RPM. If your engine is capable of exceeding 8,500 RPM you must install a transmission scatter shield or ballistic blanket. Failure to implement the above may result in serious injury or even death.
Actual disc not shown in photo.
SKU: 12521 -
SEAL TRANSMISSION FRONT INPUT, 79-92 MANUAL ALL INCLUDING TURBO
Front Input Transmission Seal, 79-92 All Manual Transmission Including Turbo
SKU: 16-1030-0603 Manufacturer SKU: 0603-16-103