Driveshaft Flange for 79-82 RX7’s
Driveshaft Flange for 79-82 RX7’s
Rear Flange – the one that bolts to the differential flange for 79-82 manual or automatic transmissions.
(U-joint not included)
| SKU: | 1502-29 |
Driveshaft Flange for 79-82 RX7’s
Rear Flange – the one that bolts to the differential flange for 79-82 manual or automatic transmissions.
(U-joint not included)
Uses OEM U-Joint #25-0600-8BB1
$52.85
Related Products:
-
Driveshaft Yoke for 79-82 RX7’s —NLA—
Driveshaft Yoke for 79-82 RX7’s Sorry, this item has been discontinued
SKU: 1503-22 -
U-JOINT for Driveshafts for RX7,2,3 71-82
U-JOINT for Driveshafts for RX7,2,3 71-82
Fits the 71-82 OEM driveshafts that have replaceable U-joints including our aftermarket RX7 shaft #2691-700
SKU: 25-0600-8BB1 Manufacturer SKU: 8BB1-25-060 -
U-JOINT NON OEM, FITS ALL WITH PART# 2691-
U-JOINT NON OEM, FITS ALL WITH PART# 2691-
For our aftermarket Steel drivshafts. Fits all our driveshafts that start with 2691.
Please Note: These will NOT work in ANY factory Mazda Driveshaft!!SKU: 2651-60 -
DRIVESHAFT YOKE, Non-Turbo Manual Trans RX7
DRIVESHAFT YOKE, Non-Turbo Manual Trans RX7
Fits 83-92 Non-Turbo RX7 Transmissions. Fits our shafts 2691-701, 2691-704, 2691-704A
Uses a 7260 Dodge u-Joint which we sell as part number 2651-60
Does not work with the factory driveshaft
SKU: 2603-22 -
DRIVESHAFT for 79-82 RX7
Aftermarket Driveshaft for 79-82 RX7
This is an aftermarket driveshaft made for us that fits all the 79-82 RX7’s — manual trans and automatics.
Uses the factory size of U-joint rear and the 2651-60 (Dodge 7260) front U-Joint. Complete, ready to bolt in.
SKU: 2691-700 -
DRIVESHAFT, 83-85 RX7 WITH TURBO TRANS SWAP
Aftermarket Driveshaft, 83-85 CAR with Turbo Transmission Swapped in, still using the stock differential
This will also work in 79-82 cars, but you will have to source a 83-85 differential flange which is discontinued new, or use an 83-85 rear end. Typically, you would swap in an 84-85 rear in a performance application because the axles are bigger and stronger than the 79-83.
SKU: 2691-2535
You May Also Like:
-
DIFF PINION BEARING, 86-92 TURBO MIDDLE, 93-11 FRONT
Differential Pinion Bearing,
Fits: 86-92 Turbo Middle
93-11 FrontSKU: 27-2200-0604 Manufacturer SKU: 0604-27-220 -
CV BOOT KIT, 86-92 TURBO INNER
Inner CV Boot Kit, 86-92 Turbo
SKU: 22-540A-M040 Manufacturer SKU: M040-22-540A -
DIFF TORSEN LSD, 84-92 NON-TURBO
Torque Sensing Limited Slip Differential, 84-92 Non Turbo
These very unique torque sensing differential limited slip units are now available for 84 and later RX-7’s. They really are the absolute best design for rear traction under ALL different conditions. It is able to transmit far more torque to the wheel that still has traction than any other type of differential. It uses the friction of the worm gear teeth and the thrust washers for the differential limiting force. In comparison with viscous type, or friction type LSD, it has the following benefits:
1) Large bias ratio torque proportioning
2) Less change of bias ratio over time of car use
3) No special differential oil or LSD additives needed
4) Improved overall traction and improved controllability under acceleration.
5) Virtually no change of torque sensing or traction control through differential temperature range.
*Note- if you have an 86-92 Non-Turbo rear end we KNOW that 86-88 N/A stub axles will work. We also KNOW that 89-92 LSD stub axles will NOT work. If you have 89-92 Non-LSD stub axles, we do NOT know that they will work with this diff. Some measuring will be necessary.SKU: MZTX-TORSEN1 -
DIFF AXLE SEAL SIDE, 86-92 TURBO
Differential Side Axle Seal, 86-92 Turbo
SKU: 27-2380-P016 Manufacturer SKU: P016-27-238 -
DIFF LSD CONE SPRING 81-88, -NEED 2
Limited Slip Differential Cone Spring 81-88,
Need 2SKU: 27-2590-M020 Manufacturer SKU: M020-27-259 -
DIFF CARRIER, 09-11 RX8
Differential Carrier, 09-11 RX8
Empty differential carrier. Does not include any gears, seals, differential, or pinion flange.
SKU: 27-1500-RA15 Manufacturer SKU: RA15-27-150