FLYWHEEL HARDWARE, STEEL 83-92 NON TURBO
Steel Flywheel Hardware 83-92 Non Turbo
| SKU: | 95180 |
FLYWHEEL HARDWARE, STEEL 83-92 NON TURBO
$45.09
Related Products:
-
REAR COUNTERWEIGHT, 13B 74-85
Rear Counterweight, 13B 74-85
SKU: 11-751A-1029 Manufacturer SKU: 1029-11-751A -
FLYWHEEL STOPPER TOOL, ALL Non-Turbo diameter flywheels
Flywheel Stopper Tool, All Non-Turbo diameter flywheels (Except RX-8’s)
Flywheel stopper makes getting the flywheel / counterweight nut off a LOT easier.
For flywheels 11 3/4″ diameter.SKU: 49-220NT Manufacturer SKU: 49-220NT -
CLUTCH KIT, 83-88 NON-TURBO
Clutch Kit, 83-88 Non-Turbo
Stock/Original EquipmentOEM Street Clutch Kit
Includes Disc, Pressure Plate, T/O Bearing, Pilot Bearing and seal, and Alignment ToolWe open every Exedy Kit to make sure that the correct Pilot Bearing and seal are included, due to Exedy rarely includes the pilot seal and sometimes has the incorrect bearing.
SKU: 10025 Manufacturer SKU: 10025 -
CLUTCH KIT, 89-92 NON-TURBO
Clutch Kit, 89-92 Non-Turbo
StreetOEM Street Clutch Kit
Includes Disc, Pressure Plate, T/O Bearing, Pilot Bearing and seal, and Alignment ToolWe open every Exedy Kit to make sure that the correct Pilot Bearing and seal are included, due to Exedy rarely includes the pilot seal and sometimes has the incorrect bearing.
SKU: 10038 Manufacturer SKU: 10038 -
FLYWHEEL SOCKET TOOL, 54MM IMPACT SOCKET
Flywheel Impact Socket Tool, 54mm, 3/4″ drive
SKU: 49-22009HD -
You May Also Like:
-
CLUTCH MASTER, 78- 2/79 RX7
Clutch Master, 78- 2/79 RX7
Hose comes out slightly to the driver sideSKU: 41-400A-8871 Manufacturer SKU: 8871-41-400A -
-
CLUTCH DISC RACE, ALL ROTARY -82
Racing Beat Race Clutch Disc, All Rotary up to 82, 4 puck
SKU: 12521 -
CLUTCH DISC STREET/STRIP HEAVY DUTY, ALL ROTARY -82
Racing Beat Clutch Disc Street/Strip Heavy Duty , All Rotary up to 82
SKU: 12509 -
SEAL TRANSMISSION FRONT INPUT, 79-92 MANUAL ALL INCLUDING TURBO
Front Input Transmission Seal, 79-92 All Manual Transmission Including Turbo
SKU: 16-1030-0603 Manufacturer SKU: 0603-16-103 -
FLYWHEEL STEEL, 74-82 WITHOUT COUNTERWEIGHT
Flywheel Steel, 74-82 Without Counterweight
Does NOT include Counterweight!!
Applications
Designed to retain enough mass for comfortable standing starts this flywheel is ideal for street use, yet it is sufficiently lighter to afford a noticeable improvement in low speed acceleration and to make shifting much smoother. For street use our lightweight steel flywheel not only allows the engine to accelerate more rapidly, but it also eliminates much of the rubbery feel that occurs at clutch engagement while shifting.Precision Machining
Precision CNC-machined from high strength steel, our flywheel assembly is mated to the Mazda OEM ring gear, then surfaced hardened using a ferritic carburizing heat-treating process, creating an extremely durable disc wear surface. The ring gear is thermally-mated to the flywheel and bolted in place for added security to prevent slippage during engagement of the starter motor.Weight Comparison
The weight of the stock flywheel is 23 lbs., compared to 13 lbs for this Flywheel. The actual reduction in inertia from stock is much greater than the weights suggest, since the stock flywheel is 1 to 2 inches thick at its outside edge.Retaining Critical Engine Balance
The installation of an aftermarket flywheel requires the use of a Mazda rear counterweight unit to ensure critical balance of the internal rotating assembly (engine rotors). As produced by Mazda, the original stock rotary flywheel features a pronounced balancing mass included in the flywheel casting. This balancing mass, combined with the stock front counterweight unit, provides the correct balance required for the optimal rotational operation of the engine rotors.To allow an aftermarket flywheel to be used on several different rotary engine applications, this balancing mass is eliminated from the design of the rotary flywheel. However, this critical balancing mass must be replaced with an alternative balance weight or risk severe engine damage due to an “unbalanced” engine. A convenient alternative is to install an appropriate rear counterweight from an automatic transmission-equipped RX-7. We offers this counterweight separately if needed.
Rear Counterweight (Required)
All aftermarket flywheels require the use of an automatic transmission rear counterweight for correct operation.Installation Hardware
Our Flywheel kits include the flywheel unit and the appropriate mounting hardware, which includes the appropriate tensile-strength hardware to attach the pressure plate to the flywheel. DO NOT use other aftermarket flywheel mounting kits with the our flywheels.
We strongly recommend replacing the throwout bearing during any clutch work to ensure trouble free performance. Also, we recommend replacing the transmission front and rear seal kit when re-installing the transmission to reduce the possibility of leakage.
Safety Warning
None of the flywheel or clutch components shown in this site should ever be allowed to exceed 10,500 RPM under any condition. This same RPM limit applies to stock components. You must use an engine RPM-limiter to prevent excessive RPM. If your engine is capable of exceeding 8,500 RPM you must install a transmission scatter shield, or ballistic blanket. Failure to implement the above may result in serious injury or even death.SKU: 11436