-10 HOSE END 90 DEG, -10 HOSE TO 18MM 90
-10 Hose End 90 Degree, -10 Hose To 18mm 90 degree
Designed specifically for 86-92 RX-7’s to fit in between the oil cooler and frame rail, where your conventional 90° bend will not. Also works for 93-95 oil filter tower, which is 18mm if you are making lines.
| SKU: | 7736-9010M18A |
| Manufacturer SKU: | 7736-9010M18A |
-10 HOSE END 90 DEG, -10 HOSE TO 18MM 90
$47.18
Related Products:
-
-10 HOSE END 90 DEGREE, TUBE 90 DEGREE
-10 Hose End 90 Degree, Tube 90 Degree
There are some custom applications where the available oil cooler line sets will just not work, and special length lines need to be assembled. We carry -10 ends in either straight, 45 degree, or 90 degree, as well as -10 hose.SKU: -10-END-90 -
-10 HOSE END, STRAIGHT
-10 Hose End, Straight
There are some custom applications where the available oil cooler line sets will just not work, and special length lines need to be assembled. We carry -10 ends in either straight, 45 degree, or 90 degree, as well as -10 hose.SKU: -10-END -
-10 PLUG PLASTIC, FITS -10 FEMALE END
-10 Plastic Plug, Fits -10 Female End
These come in very handy when you are removing the engine or cooler, to prevent debris from getting in, and oil from leaking out.
SKU: -10-PLUG -
-10 HOSE END 45 DEGREE, TUBE
-10 Hose End 45 Degree, Tube 45 Degree
There are some custom applications where the available oil cooler line sets will just not work, and special length lines need to be assembled. We carry -10 ends in either straight, 45 degree, or 90 degree, as well as -10 hose.SKU: -10-END-45
You May Also Like:
-
WEBER SHAFT LEVER, WITH STOP PIN RIGHT
Weber Shaft Lever, With Stop Pin Right
This STOP is for when the carb fuel inlet is on the Engine side, cable pulling from ABOVE the shaft.
These are for what we call “Australian Style” manifolds.All descriptions refer to a front mounted rotary engine in a rear wheel drive car.
There are two types for downdraft IDA’s: fuel inlet on engine side with throttle cable pulling from above the throttle shaft, and fuel inlet on the fender side, with the throttle cable pulling from below the throttle shaft. The manifold determines the carb orientation. It is best to have the cable pull, the idle speed screw, throttle stop, and return spring all on the same end of the carb. If this is not done, you will twist the throttle shaft, which can lead to various poor running conditions.
With this throttle STOP the throttle STOP is on the same side of the carb as the throttle PULL. Adjusted correctly this prevents the throttle shaft from being bent when full throttle is applied.
And we all know the harder you push on the gas pedal the faster you will go ??Browse our Weber Carbs, Manifolds and Parts section
SKU: MAT460-R -
EGR EXPANSION PLUG, 86-88
EGR OEM freeze plug for 86-88 Non Turbo center housing – goes below intake ports.
SKU: 52-8000-9930 Manufacturer SKU: 9930-52-800 -
ADAPTER -10 16MM THREAD, -85 COOLER AND -91 FRONT COVER
Adapter, -10, 16mm Thread, Up to 85 Cooler And Up to 91 Front Cover.
SKU: 11901 -
SCREW BRAKE ROTOR, ALL YEARS (EACH)
Brake Rotor Screw, All Years, Phillips Flat Head, Counter Sunk
Sold individuallySKU: 10-8200-9983 Manufacturer SKU: 9983-10-820 -
FREEZE PLUG LARGE, ALL FRONT & REAR HOUSING
1 3/16″ diameter Mazda OEM freeze plug for the larger holes front and rear side housings.
( uses 6-7 depending on year)
SKU: 63-0000-9930 Manufacturer SKU: 9930-63-000 -
CLUTCH RACE HARDWARE, FOR 5.5″ DOUBLE DISC
Race Clutch Hardware, For 5.5″ Double Disc Race Clutches using our Race Flywheels
SKU: 284063-HW-5.5