REAR COUNTERWEIGHT, 04-11 RX8
Rear Counterweight, 04-11 RX8
SKU: | 11-52X0-N3Z2 |
Manufacturer SKU: | N3Z2-11-52X |
REAR COUNTERWEIGHT, 04-11 RX8
$208.55
Related Products:
-
FRONT COUNTERWEIGHT, 13B 04-11 MANUAL TRANS
Front Counterweight, 13B 04-11 Manual Transmission
SKU: 11-D6X0-N3Z3 Manufacturer SKU: N3Z3-11-D6X -
FLYWHEEL STEEL, 87-11 TURBO + RX8
Steel Flywheel, 87-11 Turbo & RX8
Note: The required rear counterweight is available separately
Applications
Designed to retain enough mass for comfortable standing starts this Exedy RX-7 flywheel is ideal for street use, yet it is sufficiently lighter to afford a noticeable improvement in low speed acceleration and to make shifting much smoother. For street use this lightweight steel flywheel not only allows the engine to accelerate more rapidly but allows for quicker and more precise shifting.Precision Machining
Precision CNC-machined from a solid one-piece billet chromoly steel forging, the Exedy flywheel features a fully-machined integrated ring gear for seamless starter operation.Weight Comparison
The weight of the stock flywheel varies from 28 to 17 lbs. (depending on model year), compared to 13 lbs (excluding required counterweight – approx 4.25 lbs) for the Exedy Lightweight Steel Flywheel. The actual reduction in inertia from stock is much greater than the weights suggest, since the stock flywheel is 1 to 2 inches thick at its outside edge.Stock Flywheel Weight
87-88 RX-7 Turbo II – 28 lbs
89-91 RX-7 Turbo II – 22 lbs
93-95 RX-7 – 19 lbs
04-11 RX-8 – 17 lbsRetaining Critical Engine Balance
The installation of an aftermarket flywheel requires the use of a Mazda rear counterweight unit to ensure critical balance of the internal rotating assembly (engine rotors). As produced by Mazda, the original stock rotary flywheel features a pronounced balancing mass included in the flywheel casting. This balancing mass, combined with the stock front counterweight unit, provides the correct balance required for the optimal rotational operation of the engine rotors.To allow an aftermarket flywheel to be used on several different rotary engine applications, this balancing mass is eliminated from the design of the rotary flywheel. However, this critical balancing mass must be replaced with an alternative balance weight or risk severe engine damage due to an “unbalanced” engine. A convenient alternative is to install an appropriate rear counterweight from an automatic transmission-equipped RX-7/RX-8. We offer this counterweight separately if needed.
Rear Counterweight (Required)
All aftermarket flywheels require the use of an automatic transmission rear counterweight for correct operation.We strongly recommend replacing the throwout bearing during any clutch work to ensure trouble free performance. Also, we recommend replacing the transmission front and rear seal kit when re-installing the transmission to reduce the possibility of leakage.
Safety Warning
None of the flywheel or clutch components shown in this site should ever be allowed to exceed 10,500 RPM under any condition. This same RPM limit applies to stock components. You must use an engine RPM-limiter to prevent excessive RPM. If your engine is capable of exceeding 8,500 RPM you must install a transmission scatter shield, or ballistic blanket. Failure to implement the above may result in serious injury or even death.SKU: 11438 -
BOLT FRONT PULLEY, 04-11 RENESIS OEM
OEM Front Pulley Bolt, 04-11 Renesis
SKU: 11-4060-N3H1 Manufacturer SKU: N3H1-11-406 -
FLYWHEEL STOPPER TOOL, TURBO, AUTO TRANS AND RX8
Flywheel Stopper Tool, Turbo, Automatic Transmission And RX8 Manual
SKU: 49-220TB Manufacturer SKU: 49-220TB -
ECCENTRIC SHAFT, 13B 04-11 AUTOMATIC TRANSMISSION
Eccentric Shaft, 13B 04-11 Automatic Transmission
SKU: 11-D00D-N3H2 Manufacturer SKU: N3H2-11-D00D -