-10 HOSE END 45 DEGREE, TUBE
-10 Hose End 45 Degree, Tube 45 Degree
There are some custom applications where the available oil cooler line sets will just not work, and special length lines need to be assembled. We carry -10 ends in either straight, 45 degree, or 90 degree, as well as -10 hose.
| SKU: | -10-END-45 |
-10 HOSE END 45 DEGREE, TUBE
$31.57
Related Products:
-
-10 PLUG PLASTIC, FITS -10 FEMALE END
-10 Plastic Plug, Fits -10 Female End
These come in very handy when you are removing the engine or cooler, to prevent debris from getting in, and oil from leaking out.
SKU: -10-PLUG -
-10 HOSE END 90 DEGREE, TUBE 90 DEGREE
-10 Hose End 90 Degree, Tube 90 Degree
There are some custom applications where the available oil cooler line sets will just not work, and special length lines need to be assembled. We carry -10 ends in either straight, 45 degree, or 90 degree, as well as -10 hose.SKU: -10-END-90 -
-10 HOSE END 90 DEG, -10 HOSE TO 18MM 90
-10 Hose End 90 Degree, -10 Hose To 18mm 90 degree
Designed specifically for 86-92 RX-7’s to fit in between the oil cooler and frame rail, where your conventional 90° bend will not. Also works for 93-95 oil filter tower, which is 18mm if you are making lines.SKU: 7736-9010M18A Manufacturer SKU: 7736-9010M18A -
-10 CAP PLASTIC, FITS -10 MALE END
-10 Plastic Cap, Fits -10 Male End
Plastic Cap for male end
These come in very handy when you are removing the engine or cooler, to prevent debris from getting in.
SKU: -10-CAP
You May Also Like:
-
BATTERY HOLD DOWN, NUT 6MM BIG FLANGE
Battery Hold Down Nut, 6mm Big Flange
SKU: 00-603B-9994 Manufacturer SKU: 9994-00-603B -
WEBER SHAFT LEVER, WITH STOP PIN RIGHT
Weber Shaft Lever, With Stop Pin Right
This STOP is for when the carb fuel inlet is on the Engine side, cable pulling from ABOVE the shaft.
These are for what we call “Australian Style” manifolds.All descriptions refer to a front mounted rotary engine in a rear wheel drive car.
There are two types for downdraft IDA’s: fuel inlet on engine side with throttle cable pulling from above the throttle shaft, and fuel inlet on the fender side, with the throttle cable pulling from below the throttle shaft. The manifold determines the carb orientation. It is best to have the cable pull, the idle speed screw, throttle stop, and return spring all on the same end of the carb. If this is not done, you will twist the throttle shaft, which can lead to various poor running conditions.
With this throttle STOP the throttle STOP is on the same side of the carb as the throttle PULL. Adjusted correctly this prevents the throttle shaft from being bent when full throttle is applied.
And we all know the harder you push on the gas pedal the faster you will go ??Browse our Weber Carbs, Manifolds and Parts section
SKU: MAT460-R -
WEBER NUT 8X1.25 WITH 10MM HEX
Weber Nut 8X1.25 With 10mm Hex
These are needed for the larger bore carbs as there is not enough room to get a 12mm wrench correctly on the base nuts.
These use a 10mm wrench which gives you room to tighten the nut.
Hard to find in “not jet nut” style and in steel. They can come in handy in many other places also.Click Here for a Weber 48IDA Suggested Parts List
Browse our Weber Carbs, Manifolds and Parts section
SKU: 967-NUT -
FREEZE PLUG SMALL, FRONT HOUSING
Freeze Plug Small (3/4″ Diameter), Front Housing
(for front side housing, uses 1)SKU: 62-0000-9930 Manufacturer SKU: 9930-62-000 -
-
WEBER IDLE SPEED SCREW
Weber Idle Speed Screw
Spring is not included. It is 47600.007Browse our Weber Carbs, Manifolds and Parts section
SKU: 64625.012