RIVET PLASTIC 86-ON, PUSH BUTTON TYPE -NLA-
This item has been discontinued by Mazda
Plastic Push Button Type Rivet, 86-On
| SKU: | 56-81X0-FB01 |
| Manufacturer SKU: | FB01-56-81X |
RIVET PLASTIC 86-ON, PUSH BUTTON TYPE
$0.00
Related Products:
-
FUEL DOOR BUMP STOP, 81-85 RX7, 93-95 RX7, & 04-11 RX8
Fuel Door Bump Stop (Two per Vehicle)
Fits 81-85 RX7
93-95 RX7
04-11 RX8SKU: 70-4910-0187 Manufacturer SKU: 0187-70-491 -
FREEZE PLUG LARGE, ALL FRONT & REAR HOUSING
1 3/16″ diameter Mazda OEM freeze plug for the larger holes front and rear side housings.
( uses 6-7 depending on year)
SKU: 63-0000-9930 Manufacturer SKU: 9930-63-000 -
-
FREEZE PLUG SMALL, FRONT HOUSING
Freeze Plug Small (3/4″ Diameter), Front Housing
(for front side housing, uses 1)SKU: 62-0000-9930 Manufacturer SKU: 9930-62-000 -
FREEZE PLUG, ROTOR HOUSING @ INTAKE MANIFOLD
Freeze Plug, Rotor Housing @ Intake Manifold
SKU: 555-101 -
RIVET PLASTIC, RX8 F&R BUMPER
Front & Rear Bumper Plastic Rivet, RX8
SKU: 50-EA10-GD7A Manufacturer SKU: GD7A-50-EA1
You May Also Like:
-
-10 HOSE END, STRAIGHT
-10 Hose End, Straight
There are some custom applications where the available oil cooler line sets will just not work, and special length lines need to be assembled. We carry -10 ends in either straight, 45 degree, or 90 degree, as well as -10 hose.SKU: -10-END -
WEBER SHAFT LEVER, WITH STOP PIN RIGHT
Weber Shaft Lever, With Stop Pin Right
This STOP is for when the carb fuel inlet is on the Engine side, cable pulling from ABOVE the shaft.
These are for what we call “Australian Style” manifolds.All descriptions refer to a front mounted rotary engine in a rear wheel drive car.
There are two types for downdraft IDA’s: fuel inlet on engine side with throttle cable pulling from above the throttle shaft, and fuel inlet on the fender side, with the throttle cable pulling from below the throttle shaft. The manifold determines the carb orientation. It is best to have the cable pull, the idle speed screw, throttle stop, and return spring all on the same end of the carb. If this is not done, you will twist the throttle shaft, which can lead to various poor running conditions.
With this throttle STOP the throttle STOP is on the same side of the carb as the throttle PULL. Adjusted correctly this prevents the throttle shaft from being bent when full throttle is applied.
And we all know the harder you push on the gas pedal the faster you will go ??Browse our Weber Carbs, Manifolds and Parts section
SKU: MAT460-R -
CLUTCH RACE HARDWARE, FOR 7.25″ TWIN DISC
Race Clutch Hardware, For use with 7.25″ Twin disc Clutches using our Race Flywheels
SKU: 298062-HW-725 -
OIL PRESSURE SENDING UNIT PLUG, 1/8 BSP
Oil Pressure Sending Unit Plug, 1/8 BSP, Plug
This is to plug the oil pressure sending unit hole, in the rear side housing, when it is not being used.
It has a 1/8 British Standard Pipe thread — hard to find.
SKU: 31-000J-9950 Manufacturer SKU: 9950-31-000J -
-
CLUTCH RACE HARDWARE, FOR 5.5″ DOUBLE DISC
Race Clutch Hardware, For 5.5″ Double Disc Race Clutches using our Race Flywheels
SKU: 284063-HW-5.5