SPLIT AIR EXHAUST GASKET, 81-95 PIPE TO CAT

You May Also Like:

• 

  EXHAUST HEADER 12A, 74-78 DUAL OUTLET

  Racing Beat 12A Exhaust Header, 74-78 Dual Outlet

  SKU:

  16002

  $375.95
  Add to cart
• 

  MUFFLER POWER PULSE, 81-82 RACING BEAT

  Racing Beat Power Pulse Muffler, 81-82 

  SKU:

  16433

  $485.10
  Add to cart
• 

  EXHAUST HEADER 12A, 79-85 RX7 DUAL OUTLET

  Racing Beat 12A Exhaust Header, 79-85 RX7 Dual Outlet

  SKU:

  16125

  $375.95
  Add to cart
• 

  EXHAUST SYSTEM SINGLE, 81-82 12A

  Racing Beat Single Exhaust System, 81-82 12A

  SKU:

  16413

  $1,121.80
  Add to cart
• 

  EXHAUST PRE-SILENCER WITH DOWN PIPE, 88 CONVERTIBLE MANUAL

  Racing Beat Exhaust Pre-Silencer with Down Pipe, 88 Convertible Manual Transmission Non-Turbo

  Down Pipe with Presilencer – 1988 RX-7 Convertible Non-Turbo (w/Manual Transmission) – The 1986-92 13B 6-port engines, in stock form with the factory fuel injection, produces similar power gains with either our Header/Presilencer combo or our RX-7 Down Pipe/Presilencer combination. If you have no intentions of installing RB’s Holley intake System (or any other aftermarket carb set-up), we recommend the use of the down pipe/Presilencer combo since it offers a slightly quieter exhaust note, is easier to install and less costly. If you are intending to upgrade the intake or fuel injection system, the Header/Presilencer combo offers the greatest performance potential.

  The 1988 RX-7 Convertible (w/ Manual Transmission) Down Pipe/Presilencer combination incorporates a 2.5-inch O.D. Down Pipe and our perforated stainless steel core and stainless steel wool-packed Presilencer to boost power approximately 13% – an 18 horsepower increase on a 1987 RX 7- and maintain a comfortable exhaust noise level during full power driving.

  The replacement pipe connects to the factory exhaust manifold, and the presilencer connects to the factory Y-pipe, replacing all catalytic converters and intermediate tubing. (The downpipe cannot be used as a “bolt-up” component to replace just the catalytic converters.)

  The Racing Beat presilencer is equipped with an exhaust back-pressure tube for correct operation of the 6-port actuators. Installation of this requires the removal of the air control and check valve and the air pump. This kit includes all necessary mounting hardware, air control & check valve cover plate, and gaskets (1 Back Pressure Pick-up and 3 Replacement Pipe-to-Presilencer gaskets).

  SKU:

  16209

  $534.83
  Add to cart
• 

  EXHAUST HEADER 13B, 74-78 NO FLANGE EXCEPT PICK UP

  Racing Beat 13B Exhaust Header, 74-78 No Flange. Will not work on the Pick Up

  This rotary exhaust Header/Collector (less outlet flange) is ideal for RX-2, RX-3, RX-4, and COSMO (does not fit rotary pickup) custom exhaust installations. The flame-cut, .5-inch thick engine flange provides positive sealing and alignment. By integrating the collector with the header we reduce the effort and cost in completing the exhaust system. Engine-to-pipe gaskets are not included but are available separately. An Air Control and Check Valve Cover Plate is required when using this header with a stock intake system. 

  If the stock resonator is eliminated during installation of this unit, we strongly recommend selecting a Power Pulse Presilencer and installing it in place of the resonator to maintain a pleasant noise level and character.

  SKU:

  16007

  $389.30
  Add to cart