EXHAUST MANIFOLD GASKET, 86-92 TURBO
Exhaust Manifold Gasket, 86-92 Turbo
| SKU: | 13-4610-N386 |
| Manufacturer SKU: | N386-13-461 |
EXHAUST MANIFOLD GASKET, 86-92 TURBO
$161.45
Related Products:
-
SPLIT AIR EXHAUST GASKET, 81-95 PIPE TO CAT
Split Air Exhaust Gasket, 81-95 Split Air Pipe To Cat
SKU: 40-3750-YJZ4 Manufacturer SKU: YJZ4-40-375 -
EXHAUST CONVERTER GASKET, 86-92 ALL FRONT & REAR
EXHAUST CONVERTER GASKET, 86-92 ALL FRONT & REAR
86-92 Rx7 All Converters (Front & Rear)
SKU: 40-3050-N378 Manufacturer SKU: N378-40-305 -
EXHAUST HANGER, 86-92 @ “Y” PIPE
Exhaust Hanger at “Y” Pipe, 86-92
Go To Our FAQ for Exhaust Hangers to see the locations and part numbers of the hangers for your car.
SKU: 40-060B-N326 Manufacturer SKU: N326-40-060B -
EXHAUST HANGER, 86-92 BAND+ SLEEVE
Exhaust Hanger with Steel Band around it and a sleeve, 86-92
Go To Our FAQ for Exhaust Hangers to see the locations and part numbers of the hangers for your car.
SKU: 40-060B-N328 Manufacturer SKU: N328-40-060B -
EXHAUST HANGER, 2 SLEEVES
Exhaust Hanger, 2 Sleeves
Go To Our FAQ for Exhaust Hangers to see the locations and part numbers of the hangers for your car.
SKU: 40-1600-1114 Manufacturer SKU: 1114-40-160 -
SPLIT AIR PIPE TO MANIFOLD GASKET 86-95 TURBO
86-95 Turbo Split Air Pipe To Manifold Gasket
SKU: 13-164A-N318 Manufacturer SKU: N318-13-164A
You May Also Like:
-
-
EXHAUST STUD, RENESIS EXHAUST MANIFOLD TO ENGINE
Exhaust Stud Renesis, Exhaust Manifold to Engine (4 Required)
SKU: 13-708A-SL50 Manufacturer SKU: SL50-13-708A -
-
SPLIT AIR EXHAUST GASKET, —NLA— 79-80 HEAT EXCHANGER FRONT & REAR
Split Air Exhaust Gasket, 79-80 Split Air Pipe To Catalytic Converter
Heat Exchanger Front and RearSorry, this item has been discontinued by Mazda
SKU: 13-135B-8527 Manufacturer SKU: 8527-13-135B -
-
EXHAUST PRE-SILENCER WITH DOWN PIPE, 88 CONVERTIBLE MANUAL
Racing Beat Exhaust Pre-Silencer with Down Pipe, 88 Convertible Manual Transmission Non-Turbo
Down Pipe with Presilencer – 1988 RX-7 Convertible Non-Turbo (w/Manual Transmission) – The 1986-92 13B 6-port engines, in stock form with the factory fuel injection, produces similar power gains with either our Header/Presilencer combo or our RX-7 Down Pipe/Presilencer combination. If you have no intentions of installing RB’s Holley intake System (or any other aftermarket carb set-up), we recommend the use of the down pipe/Presilencer combo since it offers a slightly quieter exhaust note, is easier to install and less costly. If you are intending to upgrade the intake or fuel injection system, the Header/Presilencer combo offers the greatest performance potential.
The 1988 RX-7 Convertible (w/ Manual Transmission) Down Pipe/Presilencer combination incorporates a 2.5-inch O.D. Down Pipe and our perforated stainless steel core and stainless steel wool-packed Presilencer to boost power approximately 13% – an 18 horsepower increase on a 1987 RX 7- and maintain a comfortable exhaust noise level during full power driving.
The replacement pipe connects to the factory exhaust manifold, and the presilencer connects to the factory Y-pipe, replacing all catalytic converters and intermediate tubing. (The downpipe cannot be used as a “bolt-up” component to replace just the catalytic converters.)
The Racing Beat presilencer is equipped with an exhaust back-pressure tube for correct operation of the 6-port actuators. Installation of this requires the removal of the air control and check valve and the air pump. This kit includes all necessary mounting hardware, air control & check valve cover plate, and gaskets (1 Back Pressure Pick-up and 3 Replacement Pipe-to-Presilencer gaskets).
SKU: 16209